1.1 This guide covers the identification and quantitation of organic compounds by gas chromatography/mass spectrometry (GC-MS) (electron impact) that are present or extracted from water and are capable of passing through a gas chromatograph without alteration. This guide can be used to...
5.1 Purgeable organic compounds have been identified as contaminants in treated drinking water, wastewater, ground water, and Toxicity Characteristic Leaching Procedure (TCLP) leachate. These contaminants may be harmful to the environment and to people. Purge and trap sampling is a generally...
This test method covers the procedures for determining the pressure mottling and sticking, or blocking resistance of organic coatings applied on coil-coated or factory coated metal substrates prior to fabrication. The coated metal is cut into at least four, preferably six, suitably-sized...
5.1 This test method is designed to aid in identifying types of coolants. While the ash is primarily due to the inorganic inhibitors used, it is not a measure of the total inhibitor concentration because of the loss of organic inhibitors. 5.2 An ash content greater than that stated in...
1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfated oil by boiling the sample with sulfuric acid and determining the acidity of the reaction mixture. This test method is applicable only to oils that split off their...
1.1 This test method covers the determination of the organically combined sulfuric anhydride existing in a sample of sulfonated or sulfated oil, or both, by extracting the undecomposed sulfonated or sulfated fat and other fatty matter over an acidulated, concentrated salt solution, and...
4.1 Interior architectural paints are subjected in use to soiling by dirt or other stains. This test method provides a way to assess relative ease of soil or stain removal from a paint film using materials common to households. This test method includes a way to evaluate the film for washability...
1.1 This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing environments. When properly conducted, the test will enable detection of fractional molecular layers of hydrophobic...
3.1 Synthetic plasticizers are primarily esters and they are used with the more polar elastomers such as CR or NBR to improve processing, adjust hardness, and improve low temperature properties. These esters may be either monomeric or polymeric and are derived from many different organic...
5.1 Nitrosamines are a class of nitrogen-containing compounds with a known occurrence in wastewater. They may also be created in deionization and are a potential contaminant in water for reuse. The World Health Organization has issued a guideline for NDMA in drinking water at 0.1 μg/L. NDMA may...
5.1 These test methods are used to estimate the amount of volatile materials present in a material. 5.2 These test methods are useful for design purposes, service evaluation, regulatory statutes, manufacturing control, quality control, specification acceptance, development, and research. 5.3 The...
1.1 This test method covers the determination of organic impurities in commercial methanol and uses those values to determine the purity of methanol (methanol in dry basis) by gas chromatography. 1.2 This test method is applicable to the measurement of methyl formate, ethanol, acetone,...
1.1 This practice describes the determination of thermal endurance, thermal index, and relative thermal index for organic materials using the Arrhenius activation energy generated for thermal decomposition measured by thermogravimetry. 1.2 This practice is generally applicable to materials...
1.1 This test method covers the determination of retained blowing agent in extruded polystyrene foam. 1.2 This test method applies to organic blowing agents which lend themselves to a convenient analysis by gas chromatography. The method is not applicable to blowing agents such as nitrogen,...
1.1 This test method covers the energy dispersive X-ray fluorescence (EDXRF) spectrochemical analysis of trace levels of uranium and thorium in soils. Any sample matrix that differs from the general ground soil composition used for calibration (that is, fertilizer or a sample of mostly rock) would...
1.1 This specification covers the aesthetic quality requirements for decorative enamels applied to flat glass for use in building glazing. 1.2 This specification covers the requirements for flat glass, with either organic or ceramic enamels applied. 1.2.1 Glass may be annealed,...
5.1 Activated carbons used in containment systems for nuclear reactors must be capable of functioning under both normal operating conditions and those conditions which may exist following a design basis accident (DBA). Adsorbent beds that are part of recirculatory systems inside containment may be...
1.1 This test method covers laboratory determination of the time-to-failure (creep-rupture) of joints fabricated from nonbituminous organic roof membrane material. The test method covers both T-peel and lap-shear joints subjected to constant tensile load under controlled environmental...
This specification covers the requirements for electrodeposited zinc nickel alloy coatings on metals. The zinc nickel coating shall be defined as Class 1. The five chromate conversion coating types shall be defined as follows: Type A shall be with colorless conversion coatings, Type B shall be with...
This specification covers aggregates used for masonry grout. Aggregates should consist of either natural or manufactured sand, used alone or in combination with course aggregates. The course aggregates should be made up of crushed stone, gravel, or processed air-cooled iron blast-furnace slag with...
Narrow Your Results