loading
ASTM F3263-17(2025) - Standard Guide for Packaging Test Method Validation
October 1, 2025 - ASTM International

4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...

ASTM F3772-25 - Standard Test Method for Exoskeleton Use: Ladders
June 1, 2025 - ASTM International

5.1 Ladder designs can vary greatly in, for example: number and size of steps, geometry, and materials, and for a variety of industries. Fig. 2 shows examples of various ladders. 5.2.1 Example-A test requestor instructs that a lower-body exoskeleton is to be worn by five able-bodied users who are...

ASTM F3748-25 - Standard Test Method for Exoskeleton Use: Inclined Planes
February 1, 2025 - ASTM International

5.1 Inclined planes can vary greatly in, for example: slope, length, width, surface coatings and coverings, and handrails, and for a variety of industries. Fig. 1 shows images of example inclined planes. Example applications versus inclined planes are shown in Table 1. (e) Metal roof; (f) aircraft...

ASTM F665-09(2024) - Standard Classification for Vinyl Chloride Plastics Used in Biomedical Application
September 15, 2024 - ASTM International

4.1 This classification was developed to permit the addition of descriptive symbols and values for further new formulations with improved properties without complete reorganization of the standard and to facilitate the incorporation of future new test methods to keep pace with changing...

ASTM F3580-24 - Standard Test Method for Exoskeleton Use: Stairs
September 1, 2024 - ASTM International

5.1 Staircase designs can vary greatly in, for example: number of steps, staircase geometry, surface coatings and coverings, and railings, and for a variety of industries. Fig. 1 shows examples of various staircases. 5.2 Exoskeletons are being used in the industrial/occupational, military,...

ASTM D7899-24 - Standard Test Method for Measuring the Merit of Dispersancy of In-Service Engine Oils with Blotter Spot Method
July 1, 2024 - ASTM International

5.1 Dispersancy is the property that allows oil to suspend and carry away pollutants of diverse sources such as soot from combustion, metallic particles from wear, corrosion of mechanical parts, and insoluble products resulting from the aging of the oil. 5.2 When poured on a specific filter paper,...

ASTM B1028-24 - Standard Guide for the Appropriate Uses of Hand Held XRF Devices to Evaluate and Classify Copper-Bearing Scrap Materials
July 1, 2024 - ASTM International

5.1 This guide is intended for the identification and classification of copper-bearing scrap materials. Such identification and classification may include grading for commercial purposes, determining compliance (within the limits of the technology) with compositional specification requirements,...

J2964_202311 - Low-Speed Continuous Slip SAE No. 2 μPVT Procedure
November 15, 2023 - SAE International

This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 friction test is used to evaluate the friction...

J3086_202308 - Performance Classification of Headlamp Outer Lenses
August 22, 2023 - SAE International

This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements and guidelines for coating materials and plastic substrate testing.

ASTM E3304-22 - Standard Test Method for Measuring the Skid Resistance of Pavements and Other Trafficked Surfaces Using a Walking Speed Continuous Friction-Measuring Equipment (CFME) Fixed-Slip Technique
November 1, 2022 - ASTM International

1.1 This test method is used to measure skid resistance on a wide range of trafficked surfaces and for a wide variety of circumstances using a walking speed continuous friction-measuring equipment (CFME) fixed-slip measuring equipment. The fixed-slip ratio is typically 12 to 20?% but may vary...

J3210_202211 - Low-Speed Continuous Slip Durability Test
November 22, 2022 - SAE International

This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. This SAE No. 2 friction test monitors the μ-v curve for a...

ARP4784B - Definitions and Limits, Metal Material Defects and Surface and Edge Features, Fluid Couplings, Fittings, and Hose Ends
September 1, 2022 - SAE International

This SAE Aerospace Recommended Practice (ARP) is intended to provide definitions of and recommendations for drawing limits pertaining to surface and edge features on machined metal fluid fittings and is subject to change to keep pace with experience and technical advances. The subject...

J2968/1_202209 - Measurement of Material Properties for Wet Friction Materials
September 30, 2022 - SAE International

This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The specific purpose of this SAE Recommended Practice is to...

J442_202205 - Test Strip, Holder, and Gage for Shot Peening
May 4, 2022 - SAE International

This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical...

J1281_202204 - Operator Sound Pressure Level Exposure Measurement Procedure for Powered Recreational Craft
April 25, 2022 - SAE International

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level L odc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the...

ARP1052B - Selection Criteria for Internal Combustion Engines Used in Ground Support Equipment
September 30, 2021 - SAE International

This SAE Aerospace Recommended Practice (ARP) is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.

ASTM E2173-22 - Standard Guide for Disclosure of Environmental Liabilities
January 1, 2022 - ASTM International

4.1 Significance-This guide provides additional guidance to preparers of environmental disclosures; these materials are needed to address changing audience needs, the increased regulatory and accounting complexity around environmental matters, and the emergence of a variety of long-term trends and...

NR/L2/P3M/201 - Project Acceleration in a Controlled Environment (PACE)
March 6, 2021 - NR

This Network Rail standard specifies: a) the PACE lifecycle and phases; b) PACE milestones; c) PACE Products; and d) Phase Readiness Reviews. This standard is part of the Capital Delivery Core Process and relates to NR/L1/INI/P3M/100. It applies to projects that require...

J2464_202108 - Electric and Hybrid Electric Vehicle Rechargeable Energy Storage System (RESS) Safety and Abuse Testing
August 23, 2021 - SAE International

This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. It describes a body of tests which may be used as needed for abuse testing of electric or hybrid electric vehicle rechargeable energy...

J2650_202104 - Performance Requirements for Road Illumination Devices Using Light Emitting Diode (LED) Sources
April 14, 2021 - SAE International

This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes additional performance requirements specifically for road illumination devices using light emitting diode...

Advertisement