loading
ASTM D2200-26 - Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces
June 1, 2026 - ASTM International

4.1 The appearance of the various degrees of dry and wet abrasive blast cleaning, hand and power tool cleaning, and water jetting are influenced by the initial rust grades of the steel being cleaned and/or the type and condition of the coating on the existing steel. The standards and guides aid...

ASTM D5064-26 - Standard Practice for Conducting a Patch Test to Assess Coating Compatibility
June 1, 2026 - ASTM International

1.1 This practice covers the procedures for assessing coating compatibility when maintenance of an in-place coating system is being contemplated. It does not address procedures for assessing the integrity of the existing coating to determine if it can be repainted, nor does it establish the...

ASTM D7396-25 - Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting
November 1, 2025 - ASTM International

4.1 This guide describes procedures that can be used to prepare new zinc-coated surfaces for painting and improve the bond of paint to the zinc surface.

ASTM D7072-04(2026) - Standard Practice for Evaluating Accelerated Efflorescence of Latex Coatings
February 1, 2026 - ASTM International

1.1 This practice covers the evaluation of the degree to which a latex paint resists the formation of efflorescence and alkali burnout on the exposed paint surface. 1.2 This practice is designed primarily to relate efflorescence originating in the substrate to the deposit appearing on the surface...

ASTM D4470-18(2025) - Standard Test Method for Static Electrification
December 1, 2025 - ASTM International

4.1 Whenever two dissimilar materials are contacted and separated, excess electrostatic charge (triboelectric charge) will be found on these materials if at least one of the materials is a good insulator. This excess charge gives rise to electric fields which can exert forces on other objects. If...

ASTM D6337-98(2025) - Standard Practice for Physical Characterization of Woven Paint Applicator Fabrics
September 1, 2025 - ASTM International

4.1 It is important to recognize that all woven paint applicator fabrics are pile fabrics and can be a combination of several different yarns, in a range of densities, chemical compositions, and pile heights, which may influence painting performance.

ASTM D7233-08(2025) - Standard Test Method for Testing Fracture of Level Paintbrush Filaments
May 1, 2025 - ASTM International

3.1 This test method is intended to evaluate filaments for suitability of use in paintbrushes prior to manufacture. Filament fracture resistance is very important because paintbrushes are bent or flexed during painting and it is necessary that the filaments are not permanently deformed with...

ASTM E1687-25 - Standard Test Method for Determining Carcinogenic Potential of Virgin Base Oils in Metalworking Fluids
April 1, 2025 - ASTM International

5.1 The test method is based on a modification of the Ames Salmonella mutagenesis assay. As modified, there is good correlation with mouse skin-painting bioassay results for samples of raw and refined lubricating oil process streams. 5.2 Mutagenic potency in this modified assay and...

ASTM F3750-25 - Standard Practice for Assessment Method for Exoskeletons in Tool Handling
June 1, 2025 - ASTM International

1.1 This practice covers a method for testing exoskeletons on human subjects in realistic simulated working scenarios described as four test methods for overhead tool handling. 1.2 The effectiveness of exoskeletons depends on the use cases, therefore studies should be carried out in dedicated...

ASTM D6237-24 - Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
July 1, 2024 - ASTM International

1.1 This guide is intended as an information aid to painting inspectors in carrying out their tasks correctly and?efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are...

ASTM D6670-25 - Standard Practice for Full-Scale Chamber Determination of Volatile Organic Emissions from Indoor Materials/Products
February 1, 2025 - ASTM International

5.1 VOCs emitted from materials/products affect indoor air quality (IAQ) in buildings. To determine the impact of these emissions on IAQ, it is necessary to know their emission rates over time. This practice provides guidelines for using a full-scale environmental chamber for testing large...

ASTM D7804-12(2024) - Standard Test Method for Fiber Shedding of Paint Roller Covers
September 1, 2024 - ASTM International

3.1 Fibers that are released during painting can lead to a finish that is aesthetically unacceptable.

ASTM D5150-24 - Standard Test Method for Hiding Power of Architectural Paints Applied by Roller
November 1, 2024 - ASTM International

5.1 Laboratory hiding power measurements of architectural coatings generally employ blade-type applicators that lay down films of highly uniform thickness. But practical applicators, such as rollers, pads, and brushes, typically apply films that lack uniformity due to incomplete leveling, resulting...

ASTM B882-24 - Standard Specification for Pre-Patinated Copper for Architectural Applications
July 1, 2024 - ASTM International

This specification establishes of the requirements for pre-patinated (artificially aged) copper sheets and strips in ounce-weight thicknesses supplied in flat lengths for roofing, flashing, and other architectural applications. Materials made to this specification are not intended to be used for...

ASTM D1732-03(2023) - Standard Practices for Preparation of Magnesium Alloy Surfaces for Painting
November 1, 2023 - ASTM International

1.1 These practices cover two classes of treatment for preparation of magnesium alloy surfaces for painting, as follows: Class I-Chemical Treatments. Class II-Anodic Treatments. In general, the latter treatments are the more protective of the two classes. Mechanical (abrasive) treatments,...

ASTM B812-18(2024) - Standard Test Method for Resistance to Environmental Degradation of Electrical Pressure Connections Involving Aluminum and Intended for Residential Applications
April 1, 2024 - ASTM International

1.1 This test method covers all residential pressure connection systems. Detailed examples of application to specific types of connection systems, set-screw neutral bus connectors, and twist-on wire-splicing connectors are provided in Appendix X1 and Appendix X2. 1.2 The purpose of this test method...

ASTM D5066-91(2023) - Standard Test Method for Determination of the Transfer Efficiency Under Production Conditions for Spray Application of Automotive Paints—Weight Basis
June 1, 2023 - ASTM International

5.1 This test method is specifically directed at the spray painting of automobile car and light duty truck bodies. The general principles are applicable to the painting of other automotive parts. 5.2 This test method may also be used to measure transfer efficiency in full-sized...

ASTM D2805-11(2023) - Standard Test Method for Hiding Power of Paints by Reflectometry
July 1, 2023 - ASTM International

5.1 This is a precise instrumental method giving results having an absolute physical significance without reference to a comparison paint. It should be used when maximum precision and minimum subjectivity are required, as in testing specification coatings or evaluating the hiding efficiency of...

AMST21595A - Tapes, Pressure-Sensitive Adhesive, Masking, Non-Staining for Aircraft Painting Applications
September 14, 2022 - SAE International

This specification establishes requirements for pressure-sensitive adhesive tape designed for masking and color separation during aircraft painting operations.

ASTM E2408-04(2023) - Standard Test Method for Relative Extensional Viscosity of Agricultural Spray Tank Mixes
June 1, 2023 - ASTM International

4.1 Extensional viscosity is a measure of the resistance of a liquid to stretching forces, such as those occurring during the disruption of liquid films and the formation of sprays used in agriculture and other purposes including painting operations or metal working. This method for...

Advertisement