This specification covers four grades of red pigment commercially known as red lead. The pigment may be purchased in the dry form or as a paste in oil. Chemical analysis and coarse particle shall be tested to meet the requirements prescribed. Pigment, linseed oil, and moisture...
4.1 UV-A lamps are used in fluorescent penetrant and magnetic particle examination processes to excite fluorophores (dyes or pigments) to maximize the contrast and detection of discontinuities. The fluorescent dyes/pigments absorb energy from the UV-A radiation and re-emit visible...
1.1 This practice is intended to be used to disperse a chromatic pigment for subsequent testing. 1.2 This practice does not apply to white pigments. Note 1: The dispersion portion of Test Method D3022 is similar to this practice, but it utilizes a miniature sandmill rather than a...
4.1 Plastic compositions containing salts of lead, cadmium, copper, antimony, and certain other metals (as stabilizers, pigments, driers, or fillers) may stain due to the formation of a metallic sulfide when in contact with external materials that contain sulfide. The external sulfide source...
5.1 Advanced ceramic powders and porous ceramic bodies often have a very fine particulate morphology and structure that are marked by high surface-to-volume (S-V) ratios. These ceramics with high S-V ratios commonly exhibit enhanced chemical reactivity and lower sintering temperatures. Results of...
4.1 UV-A lamps are used in fluorescent penetrant and magnetic particle examination processes to excite fluorophores (dyes or pigments) to maximize the contrast and detection of discontinuities. The fluorescent dyes/pigments absorb energy from the UV-A radiation and re-emit visible...
3.1 This test method is suitable for setting specifications for the pigment content of solvent-reducible paints as well as for monitoring manufacturing quality control. 3.2 This test method provides the isolated pigment fraction from solvent-reducible paints that may be used for...
1.1 These test methods cover procedures for the chemical analysis of metallic zinc powder in the form commercially known as zinc dust for use as a pigment in paints. 1.2 The analytical procedures appear in the following order: Sections Moisture and Other Volatile Matter 7 Coarse Particles 8...
1.1 This practice covers guidelines for the evaluations of flushing vehicles for pigment dispersion using a vacuum modified sigma blade mixer, or vacuum flusher. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1...
1.1 These test methods cover the standard materials, test formula, mixing procedures, and test methods for the evaluation and production control of pigmented types of styrene-butadiene rubbers (SBR). This includes the pigmented SBR oil masterbatches. 1.2 The values stated in SI units...
5.1 This guide is designed to assist a practitioner in the selection of appropriate sample preparation methods for the analysis, comparison, and classification of paints. 5.2 It is not the intent of this guide to present comprehensive theories and methods of IR spectroscopy. It is necessary that...
This specification covers three types of zinc dust, for use as a pigment in paints. The pigments shall consist substantially of metallic zinc and shall conform to the requirements for composition prescribed. The total and metallic zinc shall be shall be tested to meet the requirements...
1.1 These test methods cover procedures for determining the relative tinting strength of paste-type printing ink dispersions by visual or instrumental evaluation of tints prepared by manual or automated mixing. 1.2 These test methods are applicable to paste-type printing inks, flushed...
This specification covers corrosion-resistant coating consisting of an inorganic aluminum particle-filled basecoat and an organic or inorganic topcoat. The basecoat is a water-dilutable slurry containing aluminum particles dispersed in a liquid binder of chromate/phosphate compounds. The organic...
5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...
This guide covers the selection and use of procedures for testing solvent-borne architectural coatings to be used on exterior, interior, or both types of surfaces. The properties that can be examined by the test methods listed herein are as follows: liquid paint properties (skinning, condition in...
5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...
5.1 The ability to collect an infrared spectrum of a liquid paint as supplied in the container from the manufacturer is of significant importance when performing qualification testing. Historically, fingerprinting a material for such purpose involved separating the components of the paint and...
5.1 Interior flat paints may become burnished in areas where clothing or upholstered furniture rub against a wall. This rubbing may cause a smoother, glossier surface at the contacted area, depending on the level or type of pigments in the paint and binder hardness. By using an automated...
1.1 This classification system standard covers nonrigid vinyl chloride polymer and copolymer classes in which the resin portion of the composition contains at least 90?% vinyl chloride. The remaining 10?% can include one or more monomers copolymerized with vinyl chloride or consist of other resins...
Narrow Your Results