loading
API REPORT BENDING MOMENT - Bending Moment Capacity Calculations for Special API Clamp/Hub Combinations
September 1, 1983 - API

I. INTRODUCTION A study was performed to provide bending moment ratings as a function of internal pressure for five API clamp-hub combinations and for a heavy duty 18 3/4-10 connector, designed to withstand a one million ft·lb bending moment at working pressure. The design of the...

PIPELINE SAFETY - PIPELINE SAFETY REGULATIONS
DOT
A description is not available for this item.
HI PIPE FRICTION MANUAL - HI PIPE FRICTION MANUAL
HI/HYDRAUL
A description is not available for this item.
ASTM F3183-21(2025) - Standard Practice for Guided Side Bend Evaluation of Polyethylene Pipe Butt Fusion Joint
December 1, 2025 - ASTM International

5.1 This standard practice is a procedure to evaluate the ductility of side bend test specimens that are a transverse section of the pipe wall and butt fusion. Side bend test specimens are prepared from bend test coupons from sample polyethylene pipe butt fusion...

PFI ES24 - PIPE BENDING METHODS, TOLERANCES, PROCESS AND MATERIAL REQUIREMENTS
December 1, 2015 - PFI

This standard covers methods, process requirements, tolerances and acceptance criteria for shop fabricated pipe bends. The bending methods described in this standard are a partial representation of commonly used processes and do not preclude the use of other methods.

ASTM A810-01(2026) - Standard Specification for Zinc-Coated (Galvanized) Steel Pipe Winding Mesh
April 1, 2026 - ASTM International

This specification deals with various designs of zinc-coated steel pipe winding mesh to be used as reinforcement for the concrete applied in the manufacture of negative buoyancy pipe needed for laying pipe in marshes or in water. This mesh can also be used as reinforcement for...

ASTM A74-26 - Standard Specification for Cast Iron Soil Pipe and Fittings
April 1, 2026 - ASTM International

This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established...

ASTM A335/A335M-26 - Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
April 1, 2026 - ASTM International

1.1 This specification covers nominal wall and minimum wall seamless ferritic alloy-steel pipe intended for high-temperature service. Pipe ordered to this specification shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding....

ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and commercial,...

ASTM A106/A106M-26 - Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service
February 15, 2026 - ASTM International

This specification covers carbon steel pipe for high-temperature service. These pipes are suitable for welding, bending, flanging, and similar forming operations. Mechanical testing of the specimens shall include tensile, bending, flattening, hydrostatic and nondestructive...

ASTM A420/A420M-26 - Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
July 1, 2026 - ASTM International

This specification covers wrought carbon steel and alloy steel pipe fittings of seamless and welded construction for use in pressure piping and pressure vessel service at low temperatures. Materials shall consist of forgings, bars, plates, seamless or fusion welded tubular products with...

ASTM B210/B210M-26 - Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
April 1, 2026 - ASTM International

1.1 This specification covers drawn seamless tubes in straight lengths and coils for general purpose and pressure applications in alloys (Note 2), tempers, and thicknesses shown in Table 2 [Table 3]. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083...

ASTM F2433-05(2025) - Standard Test Method for Determining Thermoplastic Pipe Wall Stiffness
April 1, 2025 - ASTM International

5.1 The performance under bending and compression load of a thermoplastic plastic pipe wall design obtained by this method can be used for the following: 5.1.1 To determine the stiffness of the pipe wall section. This is a function of the pipe dimensions, the wall...

ASTM A672/A672M-19(2025) - Standard Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures
September 1, 2025 - ASTM International

1.1 This specification2 covers steel pipe: electric-fusion-welded with filler metal added, fabricated from pressure-vessel quality plate of any of several analyses and strength levels and suitable for high-pressure service at moderate temperatures. Heat treatment may or may not be required...

ASTM A74-25 - Standard Specification for Cast Iron Soil Pipe and Fittings
August 15, 2025 - ASTM International

This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established...

ASTM A671/A671M-20(2025) - Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
September 1, 2025 - ASTM International

This specification covers standard requirements for electric-fusion-welded steel pipe with filler metal added, for atmospheric and lower temperatures. The steel pipe shall be fabricated from a pressure vessel quality plate of several analysis and strength levels. Several grades and...

MIL-DTL-1183/1 - FITTINGS, PIPE, CAST BRONZE, SILVER-BRAZING; BEND, PIPE, RETURN
August 20, 2019 - NPFC
A description is not available for this item.
ASTM A928/A928M-14(2025) - Standard Specification for Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler Metal
September 1, 2025 - ASTM International

1.1 This specification covers electric-fusion-welded steel pipe suitable for corrosive service. Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this specification for traditional terms such as nominal diameter, size, and nominal size. 1.2 This...

Advertisement