1.1 This practice covers the procedure for the post installation verification and acceptance of buried pipe deformation using a visible rotating laser light diode(s), a pipeline and conduit inspection analog or digital CCTV camera system and image processing software. The combination CCTV...
1.1 These test methods cover the determination of the electrical conductivity of aviation and distillate fuels with and without a static dissipator additive. The test methods normally give a measurement of the conductivity when the fuel is uncharged, that is, electrically at rest (known as the rest...
5.1 This is intended to outline O&M issues that require discussion and mutual agreement by both the optical fiber cable owner and sewer pipeline operator. The purpose is developing sufficient written procedures and practices to allow optical fiber systems to coexist as a secondary use within...
1.1 This specification covers machine-made fiberglass pipe intended for use in gravity-flow systems for conveying sanitary sewage, storm water, and some industrial wastes. Both glass-fiber-reinforc
4.1 Laser profiling assessment is a quality control tool for identifying and quantifying deformation, physical damage, and other pipe anomalies after installation, providing means and methods for determining the quality of workmanship and compliance with project specifications. Laser profiling can...
1.1 This guide covers some generally accepted laboratory methodologies that are used for determining emulsion forming tendency, wetting behavior, and corrosion mitigation properties of crude oil. 1.2 This guide does not cover detailed calculations and methods, but rather covers a range of...
5.1 Corrosion inhibitors continue to play a key role in controlling internal corrosion associated with oil and gas production and transportation. This results primarily from the industry's extensive use of carbon and low alloy steels, which, for many applications, are economic materials of...
1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications....
1.1 This practice covers procedures for testing single joints of thermoplastic pipe for gravity flow (non-pressure) sewer lines, when using either air or water under low pressure to demonstrate the integrity of the joint. This practice is used for testing 27 in. (675 mm) and larger inside diameter...
1.1 This specification covers reinforced concrete pipe intended to be used for the construction of pressure pipelines with low internal hydrostatic heads generally not exceeding 125 ft. 1.2 This specification is the inch-pound companion to Specification C361; therefore, no SI equivalents are...
1.1 This practice provides information on apparatus, safety, pre-test preparation, and procedures for conducting field tests of polyamide-12 (PA12) pressure piping systems after installation using a non-flammable and non-toxic gaseous testing media (for example, air, nitrogen, carbon dioxide), and...
1.1 This practice provides information on apparatus, safety, pre-test preparation and procedures for conducting field tests of polyethylene pressure piping systems after installation using a non-flammable and non-toxic gaseous testing media, (for example, air, nitrogen, carbon dioxide), and...
1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications....
5.1 Accurate determination of the density, relative density, or API gravity of petroleum and its products is necessary for the conversion of measured volumes to volumes or masses, or both, at the standard reference temperatures of 15?°C or (60?°F) during custody transfer. 5.2 This procedure is most...
5.1 The pour point of a petroleum product is an index of the lowest temperature of its utility for certain applications. Flow characteristics, like pour point, can be critical for the correct operation of lubricating oil systems, fuel systems, and pipeline operations. 5.2 Petroleum blending...
5.1 The pour point of a petroleum product is an index of the lowest temperature of its utility for certain applications. Flow characteristics, such as pour point, can be critical for the correct operation of lubricating systems, fuel systems, and pipeline operations. 5.2 Petroleum blending...
5.1 The pour point of a petroleum product is an index of the lowest temperature of its utility for certain applications. Flow characteristics, such as pour point, can be critical for the correct operation of lubricating systems, fuel systems, and pipeline operations. 5.2 Petroleum blending...
1.1 This specification covers materials, and test requirements for flexible fabric reinforced pipe (FFRP) made with fabric reinforcement consisting of para-aramid fibers or a combination of para-aramid and polyester fibers. 1.2 FFRP produced to this specification is for use in pressure...
Narrow Your Results