loading
AGMA PLASTIC GEAR SET - AGMA PLASTIC GEAR SET
AGMA
A description is not available for this item.
DATA PLASTIC CD - PLASTIC DIGEST
DATA
A description is not available for this item.
GM PLASTICS BINDER - ENGINEERING MATERIALS AND PROCESSES - PLASTICS BINDER
GMNA
A description is not available for this item.
ASTM D7192-26 - Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
July 1, 2026 - ASTM International

4.1 This test method is designed to provide load versus deformation response of plastic films under essentially multi-axial deformation conditions at impact velocities. This test method further provides a measure of the rate sensitivity of the plastic films to impact. 4...

ASTM D3420-21(2026) - Standard Test Method for Pendulum Impact Resistance of Plastic Film
February 1, 2026 - ASTM International

1.1 This test method covers the determination of resistance of film to impact-puncture penetration. Knowledge of how the impact energy is absorbed by the specimen while it is deforming under the impact loading, and the behavior of the specimen after yielding, is not provided by this test. No...

ASTM D3595-25 - Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Film
July 1, 2025 - ASTM International

This specification covers four types of polychlorotrifluoroethylene extruded plastic sheet and film: Type I - a transparent film with high and low moisture vapor transmission rate; Type II - a dimensionally stable transparent sheet and film with low moisture vapor...

ASTM D2838-18(2026) - Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
April 1, 2026 - ASTM International

5.1 As a result of the manufacturing process, internal stresses are locked into the film and these can be released by heating. Note 3: For any given type of film or sheeting, the temperatures at which shrinkage will begin are related to processing techniques employed to manufacture...

ASTM D2732-14(2025) - Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
December 1, 2025 - ASTM International

1.1 This test method covers determination of the degree of unrestrained linear thermal shrinkage at given specimen temperatures of plastic film and sheeting of 0.76 mm (0.030 in.) thickness or less. This test method does not cover shrinkage from loss of solvent in some materials. 1.2...

ASTM D4321-24 - Standard Test Method for Package Yield of Plastic Film
May 1, 2024 - ASTM International

1.1 This test method covers the determination of yield (area per unit mass) of plastic film. 1.2 Also described in this test method is the means for calculating nominal yield, given values for nominal density, and nominal thickness. This is needed since, in material specifications,...

ASTM F1249-25 - Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
October 1, 2025 - ASTM International

5.1 The purpose of this test method is to obtain reliable values for the WVTR of plastic film and sheeting. 5.2 WVTR is an important property of packaging materials and can often be directly related to shelf life and packaged product stability. 5.3 Data from this test method is...

ASTM D1894-24 - Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
November 15, 2024 - ASTM International

4.1 Measurements of frictional properties on a film or sheeting are made by either sliding the film or sheeting over itself or over another substance. The coefficients of friction are related to the slip properties of plastic films that are of wide interest in packaging...

ASTM D1593-22 - Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
September 1, 2022 - ASTM International

1.1 This specification covers nonrigid, unsupported vinyl chloride plastic film and sheeting in which the resin portion of the composition contains at least 90?% vinyl chloride. The remaining 10?% can include one or more monomers copolymerized with vinyl chloride, or consist of other...

ASTM D1709-24 - Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
September 1, 2024 - ASTM International

1.1 These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart. This energy is expressed in terms of the weight (mass) of the missile falling from a specified height which would result in 50?%...

ASTM D8065/D8065M-16(2023) - Standard Classification System and Basis for Specification for Specifying Plastic Films
November 1, 2023 - ASTM International

4.1 The purpose of this classification system is to provide a method of adequately identifying plastic films using a system that applies universally for plastic films. It further provides a means for specifying these films by the use of a simple line call-out...

ASTM D8136-24 - Standard Test Method for Determining Plastic Film Thickness and Thickness Variability Using a Non-Contact Capacitance Thickness Gauge
December 1, 2024 - ASTM International

1.1 This test method covers the determination of the thickness of plastic film, ranging in thickness from 2.5 to 250 μm, with a non-contact thickness gauge that uses capacitance-based technology. It includes a method to generate a series of thickness data points that can be used to...

ASTM D4204-16(2023) - Standard Practice for Preparing Plastic Film Specimens for a Round-Robin Study
November 1, 2023 - ASTM International

4.1 This practice is intended to assist task groups participating in a round-robin study with the preparation of test sets of film specimens from film samples in the form of rolls on a core. 4.2 This practice assumes that the essential features of the round-robin protocol have already...

A-A-3129 - CUSHIONING MATERIAL, FLEXIBLE OPEN CELL PLASTIC FILM (FOR PACKAGING APPLICATIONS)
October 13, 2020 - NPFC

This Commercial Item Description (CID) covers flexible, open cell, heat sealable, noncorrosive, plastic film for use in cushioning and wrapping applications.

ASTM D1922-23 - Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
May 1, 2023 - ASTM International

4.1 This test method is of value in ranking relative tearing resistance of various plastic films and thin sheeting of comparable thickness. Experience has shown the test to have its best reliability on relatively less extensible films and sheeting. Variable elongation and...

ASTM D4272/D4272M-23 - Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
August 1, 2023 - ASTM International

1.1 This test method describes the determination of the total energy impact of plastic films by measuring the kinetic energy lost by a free-falling dart that passes through the film. 1.2 Units-The values stated in either SI units or inch-pound units are to be regarded...

Advertisement