loading
AGMA PLASTIC GEAR SET - AGMA PLASTIC GEAR SET
AGMA
A description is not available for this item.
DATA PLASTIC CD - PLASTIC DIGEST
DATA
A description is not available for this item.
GM PLASTICS BINDER - ENGINEERING MATERIALS AND PROCESSES - PLASTICS BINDER
GMNA
A description is not available for this item.
SEMI MATERIALS - MATERIALS
SEMI
A description is not available for this item.
ASTM D7192-26 - Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
July 1, 2026 - ASTM International

1.1 This test method covers the determination of puncture properties of plastic films, over a range of test velocities. 1.1.1 ASTM Terminology Standard D883 has defined film as having a thickness not greater than 0.25 mm. Plastic materials having a thickness above this limit...

ASTM D2737-26 - Standard Specification for Polyethylene (PE) Plastic Tubing
April 1, 2026 - ASTM International

This specification covers polyethylene (PE) tubing pressure-rated for water. Included here are criteria for classifying PE plastic tubing materials and PE plastic tubing, and requirements and test methods for materials, workmanship, dimensions, bond strength, carbon...

ASTM D7611/D7611M-26 - Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
July 1, 2026 - ASTM International

4.1 Resin Identification Codes are used solely to identify the plastic resin used in a manufactured article. The intended manufactured articles include, but are not limited to, packaging. 4.1.1 Fig. 1 and Table 1 present the appropriate information on the way the RIC is to be incorporated...

ASTM F1488-26a - Standard Specification for Coextruded Composite Pipe
August 1, 2026 - ASTM International

1.1 This specification covers coextruded composite pipe, intended for non-pressure gravity flow drain waste or vent (DWV) service, or plastic underdrain service, or electrical or comunications conduit service produced by a coextrusion die system, in which the concentric layers are formed and...

ASTM D787-26 - Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds
July 1, 2026 - ASTM International

This specification covers the standard requirements for plasticized ethyl cellulose thermoplastic compounds suitable for injection molding and extrusion. It does not however include special materials compounded for special applications. Materials shall be ethyl cellulose...

ASTM D5511-26 - Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under High-Solids Anaerobic-Digestion Conditions
May 15, 2026 - ASTM International

1.1 This test method covers the determination of the degree and rate of anaerobic biodegradation of plastic materials in high-solids anaerobic conditions. The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated...

ASTM D1992-17(2026) - Standard Guide for Testing Synthetic Plasticizers Used in Rubber
July 1, 2026 - ASTM International

3.1 Synthetic plasticizers are primarily esters and they are used with the more polar elastomers such as CR or NBR to improve processing, adjust hardness, and improve low temperature properties. These esters may be either monomeric or polymeric and are derived from many different organic...

ASTM D3307-21(2026) - Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
July 1, 2026 - ASTM International

1.1 This specification covers melt processable molding and extrusion materials of Perfluoroalkoxy (PFA) resin. The materials are copolymers of tetrafluoroethylene and perfluoroalkoxy. 1.2 This specification is intended to provide a means for calling out plastic materials...

ASTM D8366-21a(2026) - Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF
July 1, 2026 - ASTM International

1.1 This specification covers the requirements and test methods for the material, dimensions, workmanship, and the properties of extruded sheet, rod and tubular bar manufactured from unfilled PVDF. 1.2 This specification covers the requirements and test methods for the material,...

Advertisement