loading
AGMA PLASTIC GEAR SET - AGMA PLASTIC GEAR SET
AGMA
A description is not available for this item.
DATA PLASTIC CD - PLASTIC DIGEST
DATA
A description is not available for this item.
GM PLASTICS BINDER - ENGINEERING MATERIALS AND PROCESSES - PLASTICS BINDER
GMNA
A description is not available for this item.
ASTM B793-16(2026) - Standard Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds
April 1, 2026 - ASTM International

This specification covers the standard requirements for commercial zinc casting alloys in ingot form for use in the manufacture of sheet metal forming dies, sand cast or plaster cast forming dies, and plastic injection molds. Kirksite A alloy (UNS Z35543) is intended for use in the...

AASHTO PP 92 - Standard Practice for Preparation of Test Specimens Using the Plastic Mold Compaction Device
January 1, 2019 - AASHTO

This standard practice covers the use of the plastic mold compaction device (PM device) to prepare cylindrical test specimens with an approximate 2:1 height to diameter aspect ratio for use in a variety of mechanical property testing (e.g. compressive strength, elastic modulus,...

ASTM D7474-17(2025) - Standard Practice for Determining Residual Stresses in Extruded or Molded Sulfone Plastic (SP) Parts by Immersion in Various Chemical Reagents
July 1, 2025 - ASTM International

1.1 This practice covers the evaluation of residual stresses in extruded profile or molded SP parts. The presence and relative magnitude of residual stresses are indicated by the crazing of the specimen part upon immersion in one or more of a series of chemical reagents. The specified...

FORD WSS-M98P13-F - EXTERIOR PLASTIC PERFORMANCE, MOLD-IN-COLOR ***TO BE USED WITH FORD WSS-M99P1111-A***
October 12, 2020 - FORD

This specification defines the minimum durability and performance requirements of exterior mold-in-color plastic components.

FORD WSS-M98P13-E - EXTERIOR PLASTIC PERFORMANCE, MOLD-IN-COLOR ***TO BE USED WITH FORD WSS-M99P1111-A***
October 12, 2020 - FORD

This specification defines the minimum durability and performance requirements of exterior mold-in-color plastic components.

PPP-D-1860 - DRUMS, PLASTIC, MOLDED POLYETHYLENE
NPFC
A description is not available for this item.
MIL-D-40030 - DRUMS, PLASTIC, MOLDED POLYETHYLENE
NPFC
A description is not available for this item.
MIL-B-61000 - BOTTLES, PLASTIC, MOLDED POLYETHYLENE
NPFC
A description is not available for this item.
ASTM D8366-21a(2026) - Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF
July 1, 2026 - ASTM International

1.1 This specification covers the requirements and test methods for the material, dimensions, workmanship, and the properties of extruded sheet, rod and tubular bar manufactured from unfilled PVDF. 1.2 This specification covers the requirements and test methods for the material, dimensions,...

ASTM D6110-26 - Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
July 1, 2026 - ASTM International

5.1 Before proceeding with this test method, refer to the material specification for the material being tested. Any test specimen preparation, conditioning, dimensions and testing parameters required by the materials specification shall take precedence over those required by this test method. Table...

AGMA 905 - Inspection of Molded Plastic Gears
May 24, 2017 - AGMA

This document describes industry accepted practices to inspect molded plastic gears. It identifies the unique characteristics of molded plastic gears that influence the accuracy and repeatability of gear measurements. This document does not establish a quality...

ASTM D1975-21 - Standard Test Method for Environmental Stress Crack Resistance of Plastic Injection Molded Open Head Pails
November 1, 2021 - ASTM International

1.1 This test method provides procedures for an indication of the environmental stress crack resistance of plastic injection molded open head pails, covers, and components as a summation of the effects of container design, resin, manufacturing conditions, field performance, and other...

ASTM D6780/D6780M-26 - Standard Test Methods for Water Content and Dry Density of Soil In situ by Time Domain Reflectometry (TDR)
June 1, 2026 - ASTM International

1.1 These test methods may be used to determine the water content of soils and the dry density of soils in place using Time Domain Reflectometry. 1.2 These test methods apply to soils that have 30?% or less by weight of their particles retained on the 19.0-mm [3/4-in.] sieve. 1.3 These test methods...

ASTM C780-26 - Standard Test Methods for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry
June 1, 2026 - ASTM International

1.1 These test methods cover procedures for the sampling and testing of mortars for composition and for their plastic and hardened properties, either before or during their actual use in construction. Note 1: Guide C1586 provides guidance on evaluating mortar and clarifies the purpose of...

AMS3644H - Plastic: Polyimide for Molded Rod, Bar, and Tube, Plaque, and Formed Parts
September 30, 2022 - SAE International

This specification covers a polyimide plastic in the form of isostatically molded rod, bar, and tube, unidirectionally molded plaque, and direct formed parts.

Advertisement