loading
AGMA PLASTIC GEAR SET - AGMA PLASTIC GEAR SET
AGMA
A description is not available for this item.
DATA PLASTIC CD - PLASTIC DIGEST
DATA
A description is not available for this item.
PIPELINE SAFETY - PIPELINE SAFETY REGULATIONS
DOT
A description is not available for this item.
GM PLASTICS BINDER - ENGINEERING MATERIALS AND PROCESSES - PLASTICS BINDER
GMNA
A description is not available for this item.
HI PIPE FRICTION MANUAL - HI PIPE FRICTION MANUAL
HI/HYDRAUL
A description is not available for this item.
ASTM D2290-25 - Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
December 1, 2025 - ASTM International

4.1 Split disk and ring segment tensile tests, properly interpreted, provide reasonably accurate information with regard to the apparent tensile strength of plastic pipe when employed under conditions approximating those under which the tests are made. 4.2 Ring tensile tests may...

ASTM F1498-25 - Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
December 1, 2025 - ASTM International

This specification establishes requirements for dimensions and gaging of taper pipe threads used on threaded plastic pipe and fittings. The type of pipe threads are designated by specifying in sequence the nominal pipe size, number of threads per inch, and...

ASTM F480-25 - Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
December 1, 2025 - ASTM International

This specification covers water well casing pipe and couplings made from thermoplastic materials in standard dimension ratios (SDR), SCH 40 and SCH 80. Well casing is produced in either plain end, belled end, or threaded, and is used for water wells, ground water monitoring, leak detection,...

ASTM F656-25 - Standard Specification for Primers for Use in Solvent Cement Joints of Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
December 1, 2025 - ASTM International

1.1 This specification covers requirements for primers for use with poly(vinyl chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) pipe and fittings that are to be joined by PVC solvent cements meeting the requirements of Specification D2564 and CPVC solvent cements meeting the...

ASTM F1924-25 - Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
August 1, 2025 - ASTM International

1.1 This specification describes requirements and test methods for the qualification of plastic bodied mechanical fittings for use with outside diameter controlled polyethylene (PE) gas distribution pipe, nominal 2 pipe size (IPS) and smaller complying with Specification...

ASTM F1025-19(2025) - Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe
August 1, 2025 - ASTM International

1.1 This guide specifically addresses the design and installation of full-encirclement-type band clamps for repair of gouges, punctures, or holes, and for reinforcement of polyethylene plastic pipe. Guidelines are provided for selecting and using clamps in pipe sizes 2...

ASTM F1803-25 - Standard Specification for Poly(Vinyl Chloride)?(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter?
August 1, 2025 - ASTM International

1.1 This specification covers requirements for poly(vinyl chloride) (PVC) closed profile sewer pipe and fittings with integral bell and elastomeric seal joints or plain end pipe with couplings in sizes (18?in. to 60 in.) based on a controlled inside diameter. 1.2 The values...

ASTM F2968/F2968M-24 - Standard Specification for Crosslinked Polyethylene (PEX) Pipe for Gas Distribution Applications
September 1, 2024 - ASTM International

This specification covers the requirements and corresponding test methods for outside diameter controlled, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints, made in pipe dimension ratios ranging from 6 to 17, and pressure rated...

ASTM F645-25 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
March 1, 2025 - ASTM International

1.1 This guide is intended for use in the selection, design, and installation of thermoplastic water-pressure piping systems. For specific projects, a thorough review of this guide is recommended for the purpose of selecting specific materials, methods of joining, system design factor, and any...

ASTM D2466-24 - Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
July 1, 2024 - ASTM International

This specification covers poly(vinyl chloride) (PVC) Schedule 40 pipe fittings made from four PVC plastic compounds and intended for use with Iron Pipe Size (IPS) outside-diameter plastic pipe. Fittings fabricated by welding are not included in this...

ASTM F714-25 - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
March 1, 2025 - ASTM International

1.1 This specification covers polyethylene (PE) pipe made in three standard outside diameter sizing systems, based on outside diameters of DIPS 3, IPS 4, Metric 90 mm and larger. For smaller sizes refer to Specification D3035. See 5.2.5 for guidelines on special sizes. 1...

Advertisement