loading
AGMA PLASTIC GEAR SET - AGMA PLASTIC GEAR SET
AGMA
A description is not available for this item.
DATA PLASTIC CD - PLASTIC DIGEST
DATA
A description is not available for this item.
GM PLASTICS BINDER - ENGINEERING MATERIALS AND PROCESSES - PLASTICS BINDER
GMNA
A description is not available for this item.
AWWA TANK SET - AWWA TANK SET
AWWA
A description is not available for this item.
AWWA D120 - Thermosetting FiberglassReinforced Plastic Tanks
June 7, 2019 - AWWA

This standard describes the composition, performance requirements, construction practices and workmanship, design, and methods of testing thermosetting fiberglass-reinforced plastic (FRP) tanks for the storage of water or other liquids used in water supply service. Limit of standard....

GMW3086 - Plastic Fuel Tank
May 1, 2020 - GMW

Purpose. This specification covers the material requirements for blow moldable plastic fuel tanks. Component testing and full vehicle system validation is required prior to material approval.

GMKOREA EDS-T-7530 - Test Method of Plastic Tank
November 1, 2011 - GMKOREA

This standard is applied only to gasoline all the models of sedan and van. PURPOSE This standard is to define the general requirements for plastic fuel tank.

ASTM E1067/E1067M-25 - Standard Practice for Acoustic Emission Examination of Fiberglass Reinforced Plastic Resin (FRP) Tanks/Vessels
September 1, 2025 - ASTM International

1.1 This practice covers acoustic emission (AE) examination or monitoring of fiberglass-reinforced plastic (FRP) tanks-vessels (equipment) under pressure or vacuum to determine structural integrity. 1.2 This practice is limited to tanks-vessels designed to operate at an...

API SPEC 12P - Specification for Fiberglass Reinforced Plastic Tanks
February 1, 2016 - API

General This specification covers material, design, fabrication, and testing requirements for fiberglass-reinforced plastic (FRP) tanks. Only shop-fabricated, vertical, cylindrical tanks are covered. Tanks covered by this specification are intended for aboveground and...

EEMUA PUB NO 225 - Above ground plastic tanks: A guide to their specification, installation, commissioning, inspection, maintenance, repair and disposal
October 1, 2017 - EEMUA

What is included This Publication is aimed at owners and operators of above-ground plastic tanks, which are typically cylindrical in shape. The document's content is aimed mainly at tanks being operated at atmospheric pressure or at pressures above the liquid head up to 0.5...

ASTM C1696-26 - Standard Guide for Industrial Thermal Insulation Systems
March 1, 2026 - ASTM International

4.1 When choosing a thermal insulation product or combination of products, physical, chemical and mechanical properties and the significance of those properties should be considered. ASTM test methods are usually performed under laboratory conditions and may not accurately represent field...

ASTM E1888/E1888M-17(2025) - Standard Practice for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
July 1, 2025 - ASTM International

1.1 This practice covers guidelines for acoustic emission (AE) examinations of pressurized containers made of fiberglass reinforced plastic (FRP) with balsa cores. Containers of this type are commonly used on tank trailers for the transport of hazardous chemicals. 1.2 This practice is...

ASTM D6639-25 - Standard Guide for Using the Frequency Domain Electromagnetic Method for Subsurface Site Investigations
July 1, 2025 - ASTM International

5.1 Concepts: 5.1.1 This guide summarizes the equipment, field procedures and interpretation methods used for the investigation of subsurface materials and geological structure as based on their properties to conduct, enhance or obstruct the flow of electrical currents induced in the ground by an...

ASTM D4801-08(2025) - Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater
January 1, 2025 - ASTM International

This specification covers the requirements for extruded (cast or blown) and compression-molded sheeting made from low-, medium-, and high-density polyethylenes and copolymers in specified thicknesses. Depending on the functional requirements, sheeting conforming to this specification is used in...

GMW3086 (J) - Plastic Fuel Tank Coextruded Multi-Layer
December 1, 2000 - GMW

1.Scope This specification covers the properties for coextruded multi-layer blow moldable plastic fuel tank, to meet enhanced EVAP regulation.

ASTM D6282/D6282M-25 - Standard Guide for Direct Push Soil Sampling for Environmental Site Characterizations
March 1, 2025 - ASTM International

5.1 Direct Push Soil Sampling is used extensively in environmental site characterization of soils below ground surface and can also be used for subsurface geotechnical site characterization (3, 7-13). Limited early studies have been done using Direct Push Soil Sampling for environmental...

GMKOREA EDS-T-7532 - Test Method for the Resistance to Environmental Stress-Cracking of Plastic Fuel Tank Raw Material
October 1, 2011 - GMKOREA

This standard applies to HDPE (High Density Poly Ethylene), raw material for plastic fuel tank. PURPOSE This standard aims at specifying the test method for the resistance to detergent under stress-cracking of HDPE, raw material for plastic fuel tank.

ASTM E2581-14(2023) - Standard Practice for Shearography of Polymer Matrix Composites and Sandwich Core Materials in Aerospace Applications
December 1, 2023 - ASTM International

5.1 Shearography is commonly used during product process design and optimization, process control, after manufacture inspection, and in service inspection, and can be used to measure static and dynamic axial (tensile and compressive) strain, as well as shearing, Poisson, bending, and torsional...

ASTM E3274-24 - Standard Guide for Management of Investigation-Derived Waste Associated with PFAS
February 1, 2024 - ASTM International

4.1 Perfluoroalkyl and polyfluoroalkyl substances (PFAS) are a family of more than 4700 synthetic organic chemicals. PFAS can withstand high temperatures and survive highly corrosive environments. They are used in the manufacture of coatings, surface treatments, and specialty chemicals in cookware,...

Advertisement