1.1 This test method covers the determination of retained blowing agent in extruded polystyrene foam. 1.2 This test method applies to organic blowing agents which lend themselves to a convenient analysis by gas chromatography. The method is not applicable to blowing agents such as nitrogen,...
4.1 This practice is applicable to the use of calorimetric dosimetry systems for the measurement of absorbed dose in electron beams, the qualification of electron irradiation facilities, periodic checks of the performance of electron irradiation facilities, and calibration of other dosimetry...
This standard covers the test methods for synthetic rubber lattices ABR, BR, CR, IIR, NBR, NCR, NIR, PBR, PSBR, SBR, SCR, SIR, synthetic rubber lattices with substituted carboxylic acid groups on the polymer chain, and reinforced synthetic rubber lattices. Covered tests include the procedure for...
This specification addresses the physical, chemical and test requirements for structural insulated panel (SIP) adhesives suitable for the bonding of oriented strand boards (OSB) to rigid cellular polystyrene thermal insulation core materials for general structural use. Douglas-fir to...
1.1 This specification covers PB Exterior Insulation and Finish Systems (EIFS) defined as an exterior, non-bearing wall covering providing a weather-resistant exterior wall envelope on walls required to be combustible or noncombustible, fire-resistance-rate
1.1 This specification covers the types, physical properties, and dimensions of rigid cellular polystyrene intended for use as geofoam. 1.2 This specification does not cover the layout, placement, and workmanship for proper installation and performance of rigid cellular polystyrene...
1.1 This test method covers the determination of long polystyrene blocks in SBR rubbers and styrene-reinforced latices. 1.2 Percent block styrene content may be determined in the range from 1 to 100?%. 1.3 This test method is intended for use on gel-free polymers, but it may be used on...
1.1 This guide covers some of the basic considerations for the use of expanded polystyrene (EPS) geofoam in geotechnical projects. 1.2 This guide offers a collection of information and does not recommend a course of action. This guide cannot replace education or experience and should be used...
1.1 The biofilm surface test protocol (BSTP) is a high-throughput screening approach used to determine the antimicrobial activity of either liquid agents or agents impregnated, coated, or otherwise incorporated into a medical device or surface. This practice may also be used to evaluate...
1.1 This specification is for flat, uncoated expanded polystyrene thermal insulation boards for use in exterior insulation and finish systems (EIFS) and EIFS with drainage. 1.2 EIFS and EIFS with drainage manufacturers may have requirements in addition to, or different than, those in this...
5.1 The following is a non-exclusive list of standards to which this guide applies: Guide D6062; Test Methods D4185, D4532, D6785, D7035, D7439, D7948; and Practices D6061 and D6552. 5.2 The applicability of this guide to other standards under the jurisdiction of ASTM Committee D22, but not the...
1.1 This guide describes several measurement and technical issues involved in quantifying the spread area of fixed cells. Cell spreading and the distribution of cell spread areas of a population of cells are the result of a biological response that is dependent on intracellular signaling mechanisms...
1.1 The Biofilm Surface Test Protocol (BSTP) is a high-throughput screening approach used to determine the antimicrobial activity of either liquid agents or agents impregnated, coated, or otherwise incorporated into a medical device or surface. This practice may also be used to evaluate...
4.1 Weathering reference materials are used in laboratory accelerated exposure tests to verify consistency of tests run within the same instrument at different times (repeatability) or in different instruments or different laboratories (reproducibility), using the same exposure conditions, or both....
1.1 This practice covers the determination of apparent molecular weight (MW) averages and molecular weight distributions (MWD) for THF-soluble hydrocarbon, rosin and terpene resins by size-exclusion chromatography (SEC). This technique is not absolute; it requires calibration with standards of...
This specification covers the standards for the types, physical properties and dimensions of cellular polystyrene boards with or without facings or coatings made by molding (EPS) or extrusion (XPS) of expandable polystyrene proposed for use as thermal insulation. This specification,...
4.1 The purpose of this guide is to provide direction for uniform conditioning methodology when conducting special preparations of plastic packagings as prescribed for conducting United Nations (UN) drop test. This guide provides a uniform approach for conditioning of plastic packaging intended for...
1.1 This test method covers a procedure for predicting the long-term thermal resistance (LTTR) of unfaced or permeably faced rigid gas-filled closed-cell foam insulations by reducing the specimen thickness to accelerate aging under controlled laboratory conditions (1-5) .2 Note 1: See Terminology,...
This specification covers the standards for the types, physical properties and dimensions of cellular polystyrene boards with or without facings or coatings made by molding (EPS) or extrusion (XPS) of expandable polystyrene proposed for use as thermal insulation. This specification,...
4.1 Blood and blood components are irradiated to predetermined absorbed doses to inactivate viable lymphocytes to help prevent transfusion-induced graft-versus-host disease (GVHD) in certain immunocompromised patients and those receiving related-donor products (1, 2).9 4.2 The assurance that blood...
Narrow Your Results