loading
ASTM D7483-26 - Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
July 1, 2026 - ASTM International

5.1 Many petroleum products, as well as non-petroleum materials, are used as lubricants for bearings, gears, compressor cylinders, hydraulic equipment, etc. Proper operation of this equipment depends upon the viscosity of these liquids. 5.2 Oscillating piston viscometers allow viscosity measurement...

ASTM D2624-26 - Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
July 1, 2026 - ASTM International

1.1 These test methods cover the determination of the electrical conductivity of aviation and distillate fuels with and without a static dissipator additive. The test methods normally give a measurement of the conductivity when the fuel is uncharged, that is, electrically at rest (known as the rest...

ASTM D3321-26 - Standard Test Method for Use of Handheld Refractometers for the Determination of the Freeze Point and % Glycol of Aqueous Engine Coolants
June 1, 2026 - ASTM International

1.1 This test method covers the use of portable refractometers for determining the approximate freezing point and % glycol provided by ethylene and propylene glycol-based coolants used in cooling systems. Note 1: This test method does not cover scales for other fluids that may be present on...

ASTM E3347/E3347M-26 - Standard Specification for Ballistic-Resistant Shields Used by Law Enforcement Officers
June 1, 2026 - ASTM International

1.1 This standard specifies minimum performance requirements and test methods for the ballistic resistance of shields used by U.S. law enforcement officers to protect against handgun and rifle ammunition. 1.1.1 The option for testing either handgun-rated or rifle-rated shields with a shotgun threat...

ASTM D7224-26 - Standard Test Method for Determining Water Separation Characteristics of Kerosine-Type Aviation Turbine Fuels Containing Additives by Portable Separometer
March 15, 2026 - ASTM International

1.1 This test method covers a rapid portable means for field and laboratory use to rate the ability of kerosine-type aviation turbine fuels, both neat and those containing additives, to release entrained or emulsified water when passed through coalescing material. 1.1.1 This test method is...

ASTM D7806-26 - Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Ester) and Triglyceride Content in Diesel Fuel Using Mid-Infrared Spectroscopy (FTIR Transmission Method)
May 1, 2026 - ASTM International

1.1 This test method covers the determination of fatty acid methyl ester (FAME) biodiesel and triglyceride (TAG) concentrations in traditional diesel and renewable diesel fuel blends using a portable mid-infrared spectrometer. 1.2 The method applies to samples with biodiesel concentrations...

ASTM E1444/E1444M-26 - Standard Practice for Magnetic Particle Testing for Aerospace
May 1, 2026 - ASTM International

1.1 This practice establishes minimum requirements for magnetic particle testing used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. This practice is intended for aerospace applications using the wet fluorescent method. Refer to Practice E3024/E3024M...

ASTM E1753-26a - Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films
April 1, 2026 - ASTM International

5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...

ASTM F1235-25 - Standard Consumer Safety Specification for Portable Hook-On Chairs
November 15, 2025 - ASTM International

1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair. 1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse...

ASTM E1753-26 - Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films
March 1, 2026 - ASTM International

5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...

ASTM A1038-26 - Standard Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method
February 15, 2026 - ASTM International

4.1 The hardness of a material is a defined quantity having many scales and being dependent on the way the test is performed. In order to avoid the creation of a new method involving a new hardness scale, the UCI method converts into common hardness values, for example, HV, HRC, etc. 4.2 The UCI...

ASTM F1882-26 - Standard Specification for Residential Basketball Systems
March 1, 2026 - ASTM International

1.1 This specification covers the manufacture, assembly, recommended maintenance and use of complete residential basketball systems. 1.2 This specification is intended to reduce the potential hazards associated with the installation and use of residential basketball systems. 1.3 This specification...

ASTM D8605/D8605M-26 - Standard Test Method for Use of the Pocket Penetrometer on Cohesive Soils
April 1, 2026 - ASTM International

1.1 This test method describes the use of the pocket penetrometer and allows for a simple and portable method to evaluate the consistency of cohesive soils. The pocket penetrometer is considered an index test and not an engineering test. 1.2 The test method can be used in the field or...

ASTM D8520/D8520M-23(2026) - Standard Specification for Iodotrifluoromethane (CF3I)
March 1, 2026 - ASTM International

1.1 This specification covers requirements for iodotrifluoromethane (CF3I, CAS No. 2314-97-8) as an agent for fire suppression. This specification is not intended for large-scale commercial usage. 1.2 This specification does not address fire-fighting equipment or hardware that uses CF3I or the...

ASTM D8274-25a - Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Esters) Content in Diesel Fuel Oil by Portable Rapid Mid-Infrared Analyzer
December 1, 2025 - ASTM International

5.1 Biodiesel is a fuel commodity primarily used as a blending component with diesel fuel. It is important to check the concentration of biodiesel in the diesel fuel in order to verify it is within limits or does not exceed the maximum allowable limit. 5.2 This test method is applicable for quality...

ASTM D7058-26 - Standard Test Method for Determination of the Red Dye Concentration and Estimation of Saybolt Color of Aviation Turbine Fuels and Kerosine Using a Portable Visible Spectrophotometer
March 1, 2026 - ASTM International

5.1 In the United States, high sulfur content distillate products and diesel fuel used for off-road purposes, other than aviation turbine fuel, are required to contain red dye. A similar dye requirement exists for tax-free distillates. Contamination of aviation turbine fuel by small quantities of...

ASTM E2832-26 - Standard Test Method for Measuring the Coefficient of Retroreflected Luminance of Pavement Markings in a Standard Condition of Continuous Wetting (RL-2)
March 1, 2026 - ASTM International

1.1 This test method covers a measurement of the wet retroreflective (RL-2) properties of horizontal pavement marking materials, such as traffic stripes and road surface symbols. A standardized method utilizing a standardized continuous wetting device and a portable retroreflectometer is...

ASTM F3054-26 - Standard Practice for Operations of Amusement Railway Rides, Devices, and Facilities
February 1, 2026 - ASTM International

1.1 This practice applies to operations of amusement railway ride(s) that have a track gage greater than or equal to 12 in. (305 mm) measured between the heads of the rails. This excludes patron powered ride vehicles specifically designed for children. 1.2 This standard does not apply to the...

ASTM D5011-17(2026) - Standard Practices for Calibration of Ozone Monitors Using Transfer Standards
January 1, 2026 - ASTM International

5.1 The reactivity and instability of O3 precludes the storage of O3 concentration standards for any practical length of time, and precludes direct certification of O3 concentrations as SRMs. Moreover, there is no available SRM that can be readily and directly adapted to the generation of O3...

Advertisement