loading
AWI QUALITY STANDARDS - ARCHITECTURAL WOODWORK QUALITY STANDARDS ILLISTRATED
AWI
A description is not available for this item.
ISO QUALITY ASSURANCE - QUALITY ASSURANCE FOR ANALYTICAL LABORATORIES
ISO
A description is not available for this item.
QUALITY PLANNING - QUALITY PLANNING AND ANALYSIS
ASQ
A description is not available for this item.
AAMI QUALITY SYSTEM - THE QUALITY SYSTEM COMPENDIUM: REQ & INDUSTRY PRACTICE
AAMI
A description is not available for this item.
QUALITY RELIABILITY - QUALITY, RELIABILITY & PROCESS IMPROVEMENT
IP
A description is not available for this item.
AAMI QUALITY SYSTEM CD - QUALITY SYSTEM COLLECTION CD
AAMI
A description is not available for this item.
ASTM E1125-16(2026) - Standard Test Method for Calibration of Primary Non-Concentrator Terrestrial Photovoltaic Reference Cells Using a Tabular Spectrum
June 1, 2026 - ASTM International

5.1 The electrical output of a photovoltaic device is dependent on the spectral content of the illumination source, its intensity, and the device temperature. To make standardized, accurate measurements of the performance of photovoltaic devices under a variety of light sources when the intensity...

ASTM E1018-26 - Standard Guide for Application of ASTM Recommended Cross Section and Associated Nuclear Data File
June 1, 2026 - ASTM International

4.1 The ENDF/B library in the United States and similar libraries elsewhere, such as JEFF (21), JENDL (22), and BROND (24), provide a compilation of neutron cross section and other nuclear data for use by the nuclear community. The availability of these excellent evaluations makes possible a...

ASTM E803-20(2026) - Standard Test Method for Determining the L/D?Ratio of Neutron Radiography Beams
May 1, 2026 - ASTM International

4.1 The quality of a neutron radiographic image is dependent upon many factors. The L/D ratio is one of those factors and constitutes a numerical definition of the geometry of the neutron beam. The L/D ratio required for a specific neutron radiographic examination is dependent upon the...

ASTM E3063-26 - Standard Test Method for Antimony Content Using Neutron Activation Analysis (NAA)
February 1, 2026 - ASTM International

5.1 High levels of antimony are commonly used in flame retardant formulations for various materials. NAA is a test method that can be useful for verifying these levels and, for other materials, NAA can also be useful in establishing the amount of low level contamination, if any, with high...

ASTM D7588-11(2026) - Standard Guide for FT-IR Fingerprinting of a Non-Aqueous Liquid Paint as Supplied in the Manufacturer's Container
February 1, 2026 - ASTM International

1.1 This guide covers the FT-IR fingerprinting of a liquid paint as supplied in the container without the need to separate components. Spectra collected using this technique have been found useful for paint manufacturers' quality control, trouble shooting and to verify that the paint being...

ASTM E1854-26 - Standard Practice for Ensuring Test Consistency in Neutron-Induced Displacement Damage of Electronic Parts
February 1, 2026 - ASTM International

4.1 This practice was written primarily to guide test participants in establishing, identifying, maintaining, and using suitable environments for conducting high quality neutron tests. Its development was motivated, in large measure, because inadequate controls in the neutron effects test...

ASTM D3939/D3939M-26 - Standard Test Method for Snagging Resistance of Fabrics (Mace)
January 1, 2026 - ASTM International

5.1 This test method is not considered satisfactory for acceptance testing of commercial shipments of fabrics because the between-laboratory precision of the test method is poor (see 15.1). 5.1.1 If there are differences of practical significance between reported test results for two laboratories...

ASTM D6122-25 - Standard Practice for Validation of the Performance of Multivariate Online, At-Line, Field and Laboratory Infrared Spectrophotometer, and Raman Spectrometer Based Analyzer Systems
October 1, 2025 - ASTM International

1.1 This practice covers requirements for the validation of measurements made by laboratory, field, or process (online or at-line) infrared (near- or mid-infrared analyzers, or both), and Raman analyzers, used in the calculation of physical, chemical, or quality parameters (that is,...

ASTM F3427-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Exoskeleton Test Methods
November 1, 2025 - ASTM International

4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...

ASTM F3263-17(2025) - Standard Guide for Packaging Test Method Validation
October 1, 2025 - ASTM International

4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in the...

ASTM E3010-15(2025) - Standard Practice for Installation, Commissioning, Operation, and Maintenance Process (ICOMP) of Photovoltaic Arrays
June 1, 2025 - ASTM International

1.1 This practice details the minimum requirements for installation, commissioning, operations, and maintenance processes to ensure safe and reliable power generation for the expected life of the photovoltaic system. Specifically dealing with commercial photovoltaic installations, this practice...

Advertisement