1.1 This test method monitors the reactivity of a gaseous test environment in which metal surfaces (for example, electrical contacts, assembled printed wiring boards, and so forth) and other materials subject to pollutant gas attack undergo accelerated atmospheric corrosion testing. This test...
1.1 This test method monitors the reactivity of a gaseous test environment in which metal surfaces (for example, electrical contacts, assembled printed wiring boards, and so forth) and other materials subject to pollutant gas attack undergo accelerated atmospheric corrosion testing. This test...
1.1 This test method covers the determination of particle size distribution of alumina or quartz using laser light-scattering instrumentation in the range from 0.1 μm to 500 μm. 1.2 The procedure described in this test method may be applied to other nonplastic ceramic powders. It is at the...
1.1 This specification covers autoclaved aerated concrete (AAC), a cementitious product based on calcium silicate hydrates in which low density is attained by the inclusion of an agent resulting in macroscopic voids, and in which curing is carried out using high-pressure steam. 1.2 The raw...
4.1 This test method is for estimating the relative amount of gamma alumina in calcined catalyst or catalyst carrier samples, assuming that the X-ray powder diffraction peak occurring at about 67 °2? is attributable to gamma alumina. Gamma alumina is defined as a transition alumina formed after...
1.1 This laboratory practice covers the quantitative determination of surface deposits produced during the thermal oxidation of gas turbine fuels by monitoring the oscillation frequency of a quartz crystal during thermal exposure. In this practice, "thermal oxidative stability" refers to the...
1.1 This practice describes a procedure for detecting subsurface flaws in composite panels and repair patches using flash thermography (FT), in which an infrared (IR) camera is used to detect anomalous cooling behavior of a sample surface after it has been heated with a spatially uniform light...
5.1 Refer to Guide E844 for guidance on the selection, irradiation, and quality control of neutron dosimeters. 5.2 Refer to Practice E261 for a general discussion of the determination of fast-neutron fluence rate with threshold detectors. 5.3 Pure iron in the form of foil or wire is readily...
5.1 The following is a non-exclusive list of standards to which this guide applies: Guide D6062; Test Methods D4185, D4532, D6785, D7035, D7439, D7948; and Practices D6061 and D6552. 5.2 The applicability of this guide to other standards under the jurisdiction of ASTM Committee D22, but not the...
4.1 The present trend in environmental testing of materials with electrically conductive surfaces is to produce, under accelerated laboratory conditions, corrosion and film-forming reactions that are similar to those that cause failures in service environments. In many of these procedures the parts...
1.1 This test method, one of several found valuable for the measurement of particle size, covers the determination of the particle size distribution of alumina or quartz powders (0.6?μm to 56.0 μm) using electrical sensing zone particle size analyzers. These instruments use an electric...
1.1 This practice describes procedures for shearography of polymer matrix composites and sandwich core materials made entirely or in part from fiber-reinforced polymer matrix composites. The composite materials under consideration typically contain continuous high modulus (greater than 20?GPa...
1.1 This test method covers a Soxhlet extraction procedure to determine the matrix content, reinforcement content, and filler content of composite material prepreg. Volatiles content, if appropriate, and required, is determined by means of Test Method D3530. 1.1.1 The reinforcement and filler must...
This specification covers the material characteristics, physical requirements, and sampling method appropriate to the selection of quartz-based dimension stone for general building and structural purposes. Quartz-based dimension stone shall include stone that is sawed, cut, split, or...
1.1 This ion chromatographic test method describes the determination of sulfuric acid mist in air samples collected from workplace atmospheres on a mixed cellulose ester (MCE) filter. Note 1: Other filter types such as quartz fiber, polytetrafluoroethyl
This specification covers the material and process requirements for fabricating sandwich radomes having polyimide-resin-impr
This test method covers the determination of nonvolatile content or total solids of liquid phenol, resorcinol, and melamine adhesives with or without hardener added and containing high-boiling and low-boiling volatile organic solvents or water, or both. The equipments to be used in the test shall...
5.1 Silicon (Si), a metalloid, is the second most abundant element in the earth's crust. Various forms of silica (silicon dioxide SiO2) are found in quartz, sand, and rocks. The degradation of these rocks results in silica found in natural waters. Silica in natural waters can be found as...
4.1 Both sellers and purchasers of alumina and quartz will find the test method useful to determine the specific surface area and indirectly as a measure of the particle size for material specifications, manufacturing control, and research and development.
1.1 This practice is intended to be used as a supplement to Practices E1742, E1255, E2033, and E2698. 1.2 This practice describes procedures for radiographic examination of flat panel composites and sandwich core materials made entirely or in part from fiber-reinforced polymer matrix composites....
Narrow Your Results