loading
ASTM D1123-22a(2026) - Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method
August 1, 2026 - ASTM International

1.1 These test methods cover the determination of the water present in new or unused glycol-based coolant concentrates using a volumetric (Test Method A) or an automatic coulometric titrator procedure (Test Method B). 1.2 Many carbonyl compounds react slowly with the Fischer reagent, causing...

ASTM D7881-26 - Standard Test Method for Determination of 4-Carboxybenzaldehyde and p-Toluic Acid in Purified Terephthalic Acid by Capillary Electrophoresis with Reverse Voltage Mode
July 1, 2026 - ASTM International

5.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can slow down the polymerization process; and 4-CBA is also imparting coloration to the polymer due to thermal instability. 5.2 Determining the amount of 4-CBA and p-TOL remaining from the...

ASTM D7882-26 - Standard Test Method for Determination of 4-Carboxybenzaldehyde and p-Toluic Acid in Purified Terephthalic Acid by Capillary Electrophoresis with Normal Voltage Mode
July 1, 2026 - ASTM International

5.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can slow down the polymerization process; and 4-CBA is also imparting coloration to the polymer due to thermal instability. 5.2 Determining the amount of 4-CBA and p-TOL remaining from the...

ASTM D7237-18(2026) - Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection
July 15, 2026 - ASTM International

1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...

ASTM D5114/D5114M-90(2026) - Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
July 15, 2026 - ASTM International

1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 μm (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables. 1.2 This test method does...

ASTM D5463-18(2026) - Standard Guide for Use of Test Kits to Measure Inorganic Constituents in Water
May 1, 2026 - ASTM International

5.1 Inorganic constituents in water and wastewater must be identified and measured to support effective water quality monitoring and control programs. Currently, one of the simplest, most practical and cost effective means of accomplishing this is through the use of chemical test kits and refills....

ASTM C311/C311M-26 - Standard Test Methods for Sampling and Testing Coal Ash or Natural Pozzolans for Use in Concrete
June 15, 2026 - ASTM International

1.1 These test methods cover procedures for sampling and testing coal ash and raw or calcined pozzolans for use in concrete. 1.2 The procedures appear in the following order: Sections Sampling 7 CHEMICAL ANALYSIS Reagents and apparatus 10 Moisture content 11 and 12 Loss on ignition 13 and 14...

ASTM D8607-26 - Standard Test Method for Determination of Selected Elements in Aqueous Solutions by Single Quadrupole Inductively Coupled Plasma-Mass Spectrometry (ICP-MS)
July 1, 2026 - ASTM International

1.1 This test method covers the determination of dissolved elements in ground waters, surface waters, and drinking water. It may also be used for determination of total recoverable or total element concentrations in these waters as well as wastewater, mine-impacted waters, and digested biosolids,...

ASTM D8649-26 - Standard Test Method for Determination of Select Pesticides in Water by Multiple Reaction Monitoring Liquid Chromatography Tandem Mass Spectrometry
May 1, 2026 - ASTM International

5.1 Pesticides may be used in various agricultural and household products. These products may enter waterways at low levels through run-off or misuse near water resources. Hence, there is need for a quick, easy, and robust method to determine pesticide concentration in water matrices for...

ASTM F2075-26 - Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment
June 1, 2026 - ASTM International

This specification covers engineered wood fiber for use as a playground safety surface under and around playground equipment. This specification establishes minimum requirements for the factors that determine particle size, consistency, purity, ability to drain, and heavy metal concentrations...

ASTM D8272-19(2026) - Standard Guide for Development and Optimization of D19 Chemical Analysis Methods Intended for EPA Compliance Reporting
May 1, 2026 - ASTM International

4.1 The ASTM guidance manual, Form and Style for ASTM Standards, Section A21, requires a precision and bias statement in all ASTM test methods. Section A21.2.2 states: Precision shall be estimated in accordance with the interlaboratory test program prescribed in Practice E691, Conducting an...

ASTM C581-26 - Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
April 1, 2026 - ASTM International

1.1 This practice is designed to evaluate, in an unstressed state, the chemical resistance of thermosetting resins used in the fabrication of reinforced thermosetting plastic (RTP) laminates. This practice provides for the determination of changes in the properties, described as follows, of the...

ASTM D3920-18(2026) - Standard Test Method for Strontium in Water
May 1, 2026 - ASTM International

1.1 This test method covers the determination of dissolved and total recoverable strontium in water and wastewater by atomic absorption spectroscopy. 1.2 The test method is applicable in the range from 0.1?mg/L to 1?mg/L of strontium. The range may be extended by dilution of the original sample. 1...

ASTM D888-18(2026) - Standard Test Methods for Dissolved Oxygen in Water
May 1, 2026 - ASTM International

1.1 These test methods cover the determination of dissolved oxygen in water. Three test methods are given as follows: 1.2 The precision of Test Methods A and B was carried out using a saturated sample of reagent water. It is the user's responsibility to ensure the validity of the test...

ASTM D2172/D2172M-26 - Standard Test Methods for Quantitative Extraction of Asphalt Binder from Asphalt Mixtures
May 1, 2026 - ASTM International

4.1 All of these test methods can be used for quantitative determinations of asphalt binder in asphalt mixtures and pavement samples for specification acceptance, service evaluation, control, and research. Each method prescribes the solvent or solvents and any other reagents that can be used...

ASTM F331-26 - Standard Test Method for Nonvolatile Residue of Solvent Extract from Aerospace Components (Using Flash Evaporator)
April 1, 2026 - ASTM International

This test method covers the determination of non-volatile matter, that is, residue on evaporation, in solvent extract from aerospace components, using a rotary flash evaporator. The summary of the test method, the apparatus for testing, reagents and materials for testing, and procedure for...

ASTM E2935-26 - Standard Practice for Evaluating Equivalence of Two Testing Processes
May 1, 2026 - ASTM International

1.1 This practice provides statistical methodology for conducting equivalence studies on numerical data from two sources of test results to determine if their true means, variances, or other parameters differ by no more than predetermined limits. 1.2 Applications include (1) equivalence studies for...

ASTM C910-16(2026) - Standard Test Method for Bond and Cohesion of One-Part Elastomeric Solvent Release-Type Sealants
April 1, 2026 - ASTM International

This test method details the standard procedures for the determination of the bond and cohesion of one-part elastomeric solvent release-type sealants after high- and low-temperature aging. The materials and apparatuses needed for this test procedure are an extension machine, a forced-draft type...

ASTM D5810-96(2026) - Standard Guide for Spiking into Aqueous Samples
May 1, 2026 - ASTM International

5.1 Matrix spiking is commonly used to determine the bias under specific analytical conditions, or the applicability of a test method to a particular sample matrix in that context, by determining the extent to which the spiked analyte or component is recovered from the sample matrix under these...

ASTM D5523-21(2026)e1 - Standard Test Method for Polyurethane Raw Materials: Acidity by Argentometric Determination of Hydrolyzable Chlorine in Monomeric, Aromatic Isocyanates
February 1, 2026 - ASTM International

5.1 This test method is suitable for research or for quality control to characterize TDI and MDI. 5.2 This test method was developed to overcome problems with low-level acidity determinations that use glass electrodes in the presence of reagent alcohol solvents. Reagent alcohols...

Advertisement