1.1 These test methods cover the determination of the water present in new or unused glycol-based coolant concentrates using a volumetric (Test Method A) or an automatic coulometric titrator procedure (Test Method B). 1.2 Many carbonyl compounds react slowly with the Fischer reagent, causing...
5.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can slow down the polymerization process; and 4-CBA is also imparting coloration to the polymer due to thermal instability. 5.2 Determining the amount of 4-CBA and p-TOL remaining from the...
5.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can slow down the polymerization process; and 4-CBA is also imparting coloration to the polymer due to thermal instability. 5.2 Determining the amount of 4-CBA and p-TOL remaining from the...
1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...
1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 μm (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables. 1.2 This test method does...
5.1 Inorganic constituents in water and wastewater must be identified and measured to support effective water quality monitoring and control programs. Currently, one of the simplest, most practical and cost effective means of accomplishing this is through the use of chemical test kits and refills....
1.1 These test methods cover procedures for sampling and testing coal ash and raw or calcined pozzolans for use in concrete. 1.2 The procedures appear in the following order: Sections Sampling 7 CHEMICAL ANALYSIS Reagents and apparatus 10 Moisture content 11 and 12 Loss on ignition 13 and 14...
1.1 This test method covers the determination of dissolved elements in ground waters, surface waters, and drinking water. It may also be used for determination of total recoverable or total element concentrations in these waters as well as wastewater, mine-impacted waters, and digested biosolids,...
5.1 Pesticides may be used in various agricultural and household products. These products may enter waterways at low levels through run-off or misuse near water resources. Hence, there is need for a quick, easy, and robust method to determine pesticide concentration in water matrices for...
This specification covers engineered wood fiber for use as a playground safety surface under and around playground equipment. This specification establishes minimum requirements for the factors that determine particle size, consistency, purity, ability to drain, and heavy metal concentrations...
4.1 The ASTM guidance manual, Form and Style for ASTM Standards, Section A21, requires a precision and bias statement in all ASTM test methods. Section A21.2.2 states: Precision shall be estimated in accordance with the interlaboratory test program prescribed in Practice E691, Conducting an...
1.1 This practice is designed to evaluate, in an unstressed state, the chemical resistance of thermosetting resins used in the fabrication of reinforced thermosetting plastic (RTP) laminates. This practice provides for the determination of changes in the properties, described as follows, of the...
1.1 This test method covers the determination of dissolved and total recoverable strontium in water and wastewater by atomic absorption spectroscopy. 1.2 The test method is applicable in the range from 0.1?mg/L to 1?mg/L of strontium. The range may be extended by dilution of the original sample. 1...
1.1 These test methods cover the determination of dissolved oxygen in water. Three test methods are given as follows: 1.2 The precision of Test Methods A and B was carried out using a saturated sample of reagent water. It is the user's responsibility to ensure the validity of the test...
4.1 All of these test methods can be used for quantitative determinations of asphalt binder in asphalt mixtures and pavement samples for specification acceptance, service evaluation, control, and research. Each method prescribes the solvent or solvents and any other reagents that can be used...
This test method covers the determination of non-volatile matter, that is, residue on evaporation, in solvent extract from aerospace components, using a rotary flash evaporator. The summary of the test method, the apparatus for testing, reagents and materials for testing, and procedure for...
1.1 This practice provides statistical methodology for conducting equivalence studies on numerical data from two sources of test results to determine if their true means, variances, or other parameters differ by no more than predetermined limits. 1.2 Applications include (1) equivalence studies for...
This test method details the standard procedures for the determination of the bond and cohesion of one-part elastomeric solvent release-type sealants after high- and low-temperature aging. The materials and apparatuses needed for this test procedure are an extension machine, a forced-draft type...
5.1 Matrix spiking is commonly used to determine the bias under specific analytical conditions, or the applicability of a test method to a particular sample matrix in that context, by determining the extent to which the spiked analyte or component is recovered from the sample matrix under these...
5.1 This test method is suitable for research or for quality control to characterize TDI and MDI. 5.2 This test method was developed to overcome problems with low-level acidity determinations that use glass electrodes in the presence of reagent alcohol solvents. Reagent alcohols...
Narrow Your Results