loading
ASTM C755-25 - Standard Guide for Selection of Water Vapor Retarders for Thermal Insulation
July 1, 2025 - ASTM International

4.1 Experience has shown that uncontrolled water entry into thermal insulation is the most serious factor causing impaired performance. Several ways exist by which water enters into an insulation system, the primary ones being diffusion of water vapor, air leakage carrying water...

ASTM C1015-17(2025) - Standard Practice for Installation of Cellulosic and Mineral Fiber Loose-Fill Thermal Insulation
May 1, 2025 - ASTM International

4.1 This practice recognizes that effectiveness, safety, and durability of insulation depend not only on the quality of the insulating materials, but also on their proper installation. 4.2 Improper installation of insulation can reduce its thermal effectiveness, cause fire risks and...

ASTM E336-25a - Standard Test Method for Measurement of Airborne Sound Attenuation between Rooms in Buildings
November 1, 2025 - ASTM International

1.1 The sound isolation between two spaces in a building is influenced most strongly by a combination of the direct transmission through the separating partition between the spaces (as normally measured in a laboratory) and any transmission along a number of indirect paths, referred to as flanking...

ASTM E336-25 - Standard Test Method for Measurement of Airborne Sound Attenuation between Rooms in Buildings
August 1, 2025 - ASTM International

1.1 The sound isolation between two spaces in a building is influenced most strongly by a combination of the direct transmission through the separating partition between the spaces (as normally measured in a laboratory) and any transmission along a number of indirect paths, referred to as flanking...

ASTM E1007-25 - Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
August 1, 2025 - ASTM International

1.1 This test method covers the measurement of the transmission of impact sound generated by a standard tapping machine through floor-ceiling assemblies and associated supporting structures in field situations. 1.2 Results are measurable for all types of floor-ceiling assemblies, including those...

ASTM C1617-24 - Standard Test Method for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Carbon Steel
May 1, 2024 - ASTM International

1.1 This test method covers procedures for a quantitative accelerated laboratory evaluation of the influence of extraction solutions containing ions leached from thermal insulation on the aqueous corrosion of carbon steel. The primary intent of the practice is for use with thermal...

ASTM E336-24 - Standard Test Method for Measurement of Airborne Sound Attenuation between Rooms in Buildings
September 1, 2024 - ASTM International

1.1 The sound isolation between two spaces in a building is influenced most strongly by a combination of the direct transmission through the separating partition between the spaces (as normally measured in a laboratory) and any transmission along a number of indirect paths, referred to as flanking...

ASTM F2165-24 - Standard Specification for Flexible Pre-Insulated Plastic Piping
July 1, 2024 - ASTM International

1.1 This specification covers flexible, pre-insulated plastic piping systems commonly used to convey hot and cold fluids, including piping systems that are supplied complete with plastic carrier pipe, thermal insulation, and outer jacket manufactured as an integrated system, and are supplied...

ASTM C1363-24 - Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus
March 1, 2024 - ASTM International

5.1 A need exists for accurate data on heat transfer through insulated structures at representative test conditions. The data are needed to judge compliance with specifications and regulations, for design guidance, for research evaluations of the effect of changes in materials or constructions, and...

SNZ NZS 4246 - Energy efficiency – Installing bulk thermal insulation in residential buildings
August 30, 2016 - SNZ

Inclusions This standard outlines methods of installing insulation products in common residential light-timber and steel-framed construction types. Information on the safe installation (clearances, health and safety) of insulating materials is appended. The detail in the standard is...

ASTM E2112-23 - Standard Practice for Installation of Exterior Windows, Doors and Skylights
April 15, 2023 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in residential and...

ASTM E3026-23 - Standard Guide for Readily Observable Moisture Affected Materials and Conditions Conducive to Elevated Moisture in Commercial Buildings: Visual Moisture Assessment Process
March 15, 2023 - ASTM International

4.1 Use-This guide is intended for use on a voluntary basis by parties who wish to obtain a limited survey of commercial real estate to assess for readily observable moisture affected materials and physical deficiencies conducive to elevated moisture as part of a commercial real estate transaction...

ASTM E3026-23e1 - Standard Guide for Readily Observable Moisture Affected Materials and Conditions Conducive to Elevated Moisture in Commercial Buildings: Limited Moisture Assessment Process
March 15, 2023 - ASTM International

4.1 Use-This guide is intended for use on a voluntary basis by parties who wish to obtain a limited survey of commercial real estate to assess for readily observable moisture affected materials and physical deficiencies conducive to elevated moisture as part of a commercial real estate transaction...

ASTM E2511-17(2023) - Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies
February 1, 2023 - ASTM International

1.1 This guide describes the types of project-specific construction conditions that need to be communicated by means of drawings ("details") for the purpose of constructing Exterior Insulation and Finish System (EIFS)-clad barrier and drainage wall assemblies. EIFS manufacturers provide...

ASTM E336-23 - Standard Test Method for Measurement of Airborne Sound Attenuation between Rooms in Buildings
January 1, 2023 - ASTM International

1.1 The sound isolation between two spaces in a building is influenced most strongly by a combination of the direct transmission through the nominally separating building element (as normally measured in a laboratory) and any transmission along a number of indirect paths, referred to as flanking...

ASTM E1007-21 - Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
April 15, 2021 - ASTM International

1.1 This test method covers the measurement of the transmission of impact sound generated by a standard tapping machine through floor-ceiling assemblies and associated supporting structures in field situations. 1.2 Results are measurable for all types of floor-ceiling assemblies, including those...

ASTM C755-20 - Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation
March 1, 2020 - ASTM International

4.1 Experience has shown that uncontrolled water entry into thermal insulation is the most serious factor causing impaired performance. Several ways exist by which water enters into an insulation system, the primary ones being diffusion of water vapor, air leakage carrying water...

Advertisement