1.1 This practice covers the determination of the resistance of plastics to staining in the presence of sulfides. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use....
4.1 This test method provides a technique for evaluating mold growth resistance characteristics of Wet Blue and Wet White, and should assist in the prediction of storage time before molding occurs. 4.2 The degree of correlation between this test and commercial quantities of Wet Blue and Wet...
1.1 This test method covers the determination of the abrasion resistance of textile fabrics using the Martindale abrasion tester. The method is generally applicable to knit, woven, and nonwoven fabrics; however, material thickness may limit suitability for testing due to specimen holder...
1.1 This test method covers the determination of the resistance to the formation of pills and other related surface changes on textile fabrics using the Martindale tester. Note 1: For other methods, if testing the pilling resistance of textiles, refer to Test Methods D3511/D3511M,...
1.1 This test method covers procedures for evaluating the relative mar resistance of a high gloss coating applied to a flat, rigid surface. Wet rub and dry rub abrasion tests are described. To fully characterize a coating's mar resistance, both tests should be run. Note 1: Dry...
1.1 This test method is used to determine the resistance of plastics to breakage by flexural shock as indicated by the energy extracted from standardized (see Note 1) pendulum-type hammers, mounted in standardized machines, in breaking standard specimens with one pendulum swing. This test...
1.1 This practice provides a means to determine the blowout resistance of a room-temperature vulcanized elastomer system (RTV) using a standard fixture. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This...
1.1 This test method covers procedures for evaluating the relative mar resistance of high gloss coatings. Two test methods are included. Test Method A uses a device that rotates the test specimen on a vertical axis, against the sliding rotation of two abrading wheels. Test Method B uses a...
1.1 This test method rates the non-steady state thermal resistance or insulating characteristics of flame resistant clothing materials subjected to a continuous, standardized radiant heat exposure. 1.1.1 This test method is not applicable to clothing materials that are not flame resistant....
5.1 This practice is intended to provide a list of standard procedures for test programs investigating the chemical resistance of a geomembrane with a liquid waste, leachate, or chemical. This practice should be used in the absence of other specifications required for the particular...
5.1 Due to hydraulic pressure that may be present on some applications, engineers need to understand the capability of these products to resist this pressure. This test allows engineers to compare products and verify pullout strength. 5.2 Hydraulic pullout resistance is a function of locking...
6.1 The environmental chamber method is an accelerated test for determining the resistance of Wet Blue and Wet White to the growth of fungi, the causal agent of mold. See Test Method D3273., 6.2 The environmental chamber method is useful in estimating the performance of fungicides and should...
This test method covers the procedures for determining the pressure mottling and sticking, or blocking resistance of organic coatings applied on coil-coated or factory coated metal substrates prior to fabrication. The coated metal is cut into at least four, preferably six, suitably-sized...
1.1 This test method covers the determination of the crazing resistance of fired glazed whitewares using the autoclave treatment and under the conditions specified in this test method. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses...
1.1 This test method is used to measure the resistance of materials used in protective clothing to penetration by blood-borne pathogens using a surrogate microbe under conditions of continuous liquid contact. Protective clothing material pass/fail determinations are based on the detection of...
4.1 Many types of printed matter, notably container labels, packaging materials, magazine and book covers, must be resistant to liquid materials that may contact them advertently or inadvertently. This practice permits an assessment of resistance of printed matter to several types of liquids...
1.1 This specification covers requirements, test methods, and marking requirements for system components when tested with nominal SDR9 crosslinked polyethylene (PEX) tubing as a system. Systems are intended for 100 psi (0.69 MPa) water service up to and including a maximum working temperature of...
1.1 This specification covers prefabricated modified bituminous sheet materials reinforced with polyester fabric as the primary reinforcement, with or without granules, which use styrene butadiene styrene (SBS) thermoplastic elastomer as the primary modifier and are intended for use in the...
5.1 This test method is an index test for determining the puncture resistance of geomembranes and related products. The use of this test method is to establish an index value by providing standard criteria and a basis for uniform reporting. 5.2 This test method is considered satisfactory for...
1.1 This test method covers the procedure for determining the drying time of oxidative-drying printing inks (also referred to as "sheetfed inks") by squalene resistance of printed ink films. 1.2 This test method is applicable to all paste inks that dry primarily by oxidation regardless of...