4.1 In 2014, the U.S. EPA published the final rules adding renewable fuel pathways under the RFS Program. The rules qualified kernel fiber as a cellulosic feedstock meeting the 60?% greenhouse gas (GHG) reduction and qualifies for the generation of D3 RINs. These rules allow...
1.1 This specification addresses the airworthiness requirements related to structural durability for the design of small aeroplanes. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Levels 1 through 4 Normal...
1.1 This specification covers standard sand for use in the testing of hydraulic cements. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and...
1.1 This practice is intended to satisfy the demand for basic safety information, which should be understood by each paintball game participant, prior to the start of the player's first game on the day of play. 1.2 The information specifies rules of personal conduct, which might affect the...
1.1 This specification covers the establishment of requirements of liquid automotive fuels for ground vehicles equipped with spark-ignition engines. 1.2 This specification describes various characteristics of automotive fuels for use over a wide range of operating conditions. It provides for a...
1.1 These test methods describe a procedure for determining the amount of volatile matter of any kind that is driven off from a test specimen under a specific set of temperature and time conditions. These test methods determine only the mass of material lost, not its identity. 1.2 These test...
1.1 This specification covers international standards for ice protection aspects of airworthiness and design for "general aviation" aircraft. 1.2 The applicant for a design approval must seek the individual guidance of their respective civil aviation authority (CAA) body concerning the use of this...
1.1 This specification covers international standards for the environmental system aspects of airworthiness and design for "small" aircraft. 1.2 The applicant for a design approval must seek the individual guidance of their respective CAA body concerning the use of this specification as part of a...
1.1 This specification covers the required release and retention characteristics of ski-binding-boot (S-B-B) systems. This specification is applicable to all recreational snow skiing bindings that have safety release mechanisms. Specifically, this performance standard establishes the minimum...
1.1 This test method covers determination of the compressive strength of hydraulic cement mortars, using 50 mm [2?in.] cube specimens. Note 1: Test Method C349 provides an alternative procedure for this determination (not to be used for acceptance tests). 1.2 This test method covers the application...
1.1 This test method, which is applicable only to portland cements and portland-limestone cements, covers the determination of the expansion of mortar bars made from a mixture of portland cement or portland-limestone cement and gypsum in such proportions that the mixture has a sulfur trioxide (SO3)...
1.1 This terminology covers definitions of technical terms used in the rubber industry. Terms that are generally understood or adequately defined in other readily available sources are not included. 1.2 Definitions for terms that have been established by other bodies recognized as expert in the...
4.1 Creep-fatigue testing is typically performed at elevated temperatures and involves the sequential or simultaneous application of the loading conditions necessary to generate cyclic deformation/damage enhanced by creep deformation/damage or vice versa. Unless such tests are performed in vacuum...
1.1 This specification addresses the airworthiness requirements for the installation and integration of propeller systems. 1.2 This specification is applicable to aeroplanes as defined in F44 terminology standard. 1.3 The applicant for a design approval must seek the individual guidance to their...
1.1 This practice covers guidance for fire extinguishing agent concentration testing used in determining the distribution and concentration of fire extinguishing agents when discharged in an aircraft powerplant compartment. This practice is limited to vaporizing liquid fire extinguishing agents or...
1.1 This practice covers procedures commonly used in the paint industry to formulate paints and coating materials. It describes procedures for calculating formulation values for weight solids, volume solids, solvent content, volatile organic compound (VOC) content, hazardous air pollutant (HAP)...
1.1 This practice covers minimum requirements for the design and manufacture of combustion turbine engines for light sport category aircraft, visual flight rules (VFR) or instrument flight rules (IFR) into instrument meteorological conditions (IMC) (no known icing) use. 1.2 Units-The...
1.1 This specification covers international standards for ice protection aspects of airworthiness and design for "general aviation" aircraft. 1.2 The applicant for a design approval must seek the individual guidance of their respective civil aviation authority (CAA) body concerning the use of this...
1.1 This specification covers airworthiness requirements for establishing general limitations and information to be contained in the aeroplane flight manual. This specification specifies what information shall be provided and does not state how such information shall be presented unless this is...