1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 The values stated in SI...
4.1 The appearance of the various degrees of dry and wet abrasive blast cleaning, hand and power tool cleaning, and water jetting are influenced by the initial rust grades of the steel being cleaned and/or the type and condition of the coating on the existing steel. The standards and guides...
1.1 This guide covers general procedures for conducting a detailed assessment of the condition of aged coatings on steel structures and the extent of rust breakthrough of the coated surface. Additional assessment may be required to support coating failure analyses or other job-specific needs...
1.1 This test method covers the ability of steam-turbine oils to prevent the rusting of horizontal and vertical ferrous surfaces when water becomes mixed with the oil. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only....
1.1 This practice covers procedures to evaluate the compatibility of coatings with additives used to prevent flash rusting of steel before application of coatings. 1.2 The additives are used with vapor blast, wet abrasive blast (WAB), low or high pressure water cleaning (LPWC, HPWC), and...
5.1 The compatibility of oils can be important for users of oil-lubricated equipment. Mixing of two oils can produce a substance markedly inferior to either of its constituent materials. One or more of the following can occur: 5.1.1 A mixture of incompatible oils most often forms a precipitate. The...
5.1 In many instances, such as in the gears of a steam turbine, water can become mixed with the lubricant, and rusting of ferrous parts can occur. This test indicates how well inhibited mineral oils aid in preventing this type of rusting. This test method is also used for testing...
1.1 This specification covers mineral and synthetic (API group I, II, III, or IV) oils used in steam and gas turbine lubrication systems where the performance requirements demand highly refined mineral or synthetic base oils compounded with rust and oxidation inhibitors plus selected...
5.1 Knowledge of the amount of ash-forming material present in a product can provide information as to whether or not the product is suitable for use in a given application. Ash can result from oil or water-soluble metallic compounds or from extraneous solids such as dirt and rust.
1.1 This guide describes the procedure for cleaning metal surfaces to obtain good adhesion of electrodeposited metals. The degree of cleanliness required for metals to be electroplated is greater than for most other finishes. Methods of removal of heat-treat or mill scale are not included in these...
3.1 The amount of rusting beneath or through a paint film is a significant factor in determining whether a coating system should be repaired or replaced. This practice provides a standardized means for quantifying the amount and distribution of visible surface rust. 3.2 The degree of...
This specification covers the minimum requirements for full-thickness interior gypsum plastering on gypsum, metal, masonry, or monolithic concrete bases designed or prepared to receive gypsum plaster. Gypsum plaster applied to the interior side of exterior walls of masonry or concrete shall be...
1.1 This test method covers the evaluation of the oxidation stability of inhibited steam-turbine oils in the presence of oxygen, water, and copper and iron metals at an elevated temperature. This test method is limited to a maximum testing time of 10?000?h. This test method is also used for testing...
1.1 This test method covers a test procedure for evaluating the rust and corrosion inhibiting properties of a gear lubricant while subjected to water contamination and elevated temperature in a bench-mounted hypoid differential housing assembly.2 This test method is commonly referred to as...
5.1 In many instances, such as in the gears of a steam turbine, water can become mixed with the lubricant, and rusting of ferrous parts can occur. This test indicates how well inhibited mineral oils aid in preventing this type of rusting. This test method is also used for testing...
1.1 This test method covers the evaluation of the rust-preventive properties of metal preservatives under conditions of high humidity. 1.2 The values stated in SI units are to be regarded as the standard except where the test apparatus or consumable parts are only available in other units....
This specification covers round, square, rectangular, and special shape electric-resistance-
4.1 The procedures described in this practice are intended to aid in evaluating the performance of coatings on various metal panels including either new or rusted steel. 4.2 The relative durability of paints in outdoor exposures can be very different depending on the location of the exposure...
1.1 This test method covers components of ferrous metal fastener assemblies, excluding those of stainless steel, such as fasteners, stress plates, and batten bars used in low-slope roofing and waterproofing, to a sulfurous acid environment. This test method evaluates relative corrosion resistance...
This specification covers the requirements for standard-type needle roller bearings with drawn outer rings, full complement, without inner rings, and with either open (Type B) or closed ends (Type M). Materials covered by this specification are needle rollers which shall be manufactured from steel,...
Narrow Your Results