loading
ASTM D6557-26 - Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils
June 1, 2026 - ASTM International

1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 The values stated in SI...

ASTM D2200-26 - Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces
June 1, 2026 - ASTM International

4.1 The appearance of the various degrees of dry and wet abrasive blast cleaning, hand and power tool cleaning, and water jetting are influenced by the initial rust grades of the steel being cleaned and/or the type and condition of the coating on the existing steel. The standards and guides...

ASTM D5065-26 - Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces
June 1, 2026 - ASTM International

1.1 This guide covers general procedures for conducting a detailed assessment of the condition of aged coatings on steel structures and the extent of rust breakthrough of the coated surface. Additional assessment may be required to support coating failure analyses or other job-specific needs...

ASTM D3603-20(2026) - Standard Test Method for Rust-Preventing Characteristics of Steam Turbine Oil in the Presence of Water (Horizontal Disk Method)
March 1, 2026 - ASTM International

1.1 This test method covers the ability of steam-turbine oils to prevent the rusting of horizontal and vertical ferrous surfaces when water becomes mixed with the oil. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only....

ASTM D5367-26 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Additives Used to Prevent Flash Rusting of Steel When Vapor, Water, or Water/Abrasive Blasted
June 1, 2026 - ASTM International

1.1 This practice covers procedures to evaluate the compatibility of coatings with additives used to prevent flash rusting of steel before application of coatings. 1.2 The additives are used with vapor blast, wet abrasive blast (WAB), low or high pressure water cleaning (LPWC, HPWC), and...

ASTM D7155-20(2026) - Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
March 1, 2026 - ASTM International

5.1 The compatibility of oils can be important for users of oil-lubricated equipment. Mixing of two oils can produce a substance markedly inferior to either of its constituent materials. One or more of the following can occur: 5.1.1 A mixture of incompatible oils most often forms a precipitate. The...

ASTM D665-25 - Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
July 1, 2025 - ASTM International

5.1 In many instances, such as in the gears of a steam turbine, water can become mixed with the lubricant, and rusting of ferrous parts can occur. This test indicates how well inhibited mineral oils aid in preventing this type of rusting. This test method is also used for testing...

ASTM D4304-25 - Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines
November 1, 2025 - ASTM International

1.1 This specification covers mineral and synthetic (API group I, II, III, or IV) oils used in steam and gas turbine lubrication systems where the performance requirements demand highly refined mineral or synthetic base oils compounded with rust and oxidation inhibitors plus selected...

ASTM D482-25 - Standard Test Method for Ash from Petroleum Products
October 1, 2025 - ASTM International

5.1 Knowledge of the amount of ash-forming material present in a product can provide information as to whether or not the product is suitable for use in a given application. Ash can result from oil or water-soluble metallic compounds or from extraneous solids such as dirt and rust.

ASTM B322-99(2025) - Standard Guide for Cleaning Metals Prior to Electroplating
November 1, 2025 - ASTM International

1.1 This guide describes the procedure for cleaning metal surfaces to obtain good adhesion of electrodeposited metals. The degree of cleanliness required for metals to be electroplated is greater than for most other finishes. Methods of removal of heat-treat or mill scale are not included in these...

ASTM D610-25 - Standard Practice for Evaluating Degree of Rusting on Painted Steel Surfaces
June 1, 2025 - ASTM International

3.1 The amount of rusting beneath or through a paint film is a significant factor in determining whether a coating system should be repaired or replaced. This practice provides a standardized means for quantifying the amount and distribution of visible surface rust. 3.2 The degree of...

ASTM C842-05(2025) - Standard Specification for Application of Interior Gypsum Plaster
October 1, 2025 - ASTM International

This specification covers the minimum requirements for full-thickness interior gypsum plastering on gypsum, metal, masonry, or monolithic concrete bases designed or prepared to receive gypsum plaster. Gypsum plaster applied to the interior side of exterior walls of masonry or concrete shall be...

ASTM D943-25 - Standard Test Method for Oxidation Characteristics of Inhibited Mineral Oils
October 1, 2025 - ASTM International

1.1 This test method covers the evaluation of the oxidation stability of inhibited steam-turbine oils in the presence of oxygen, water, and copper and iron metals at an elevated temperature. This test method is limited to a maximum testing time of 10?000?h. This test method is also used for testing...

ASTM D7038-25 - Standard Test Method for Evaluation of Moisture Corrosion Resistance of Automotive Gear Lubricants
July 1, 2025 - ASTM International

1.1 This test method covers a test procedure for evaluating the rust and corrosion inhibiting properties of a gear lubricant while subjected to water contamination and elevated temperature in a bench-mounted hypoid differential housing assembly.2 This test method is commonly referred to as...

ASTM D665-24 - Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
December 1, 2024 - ASTM International

5.1 In many instances, such as in the gears of a steam turbine, water can become mixed with the lubricant, and rusting of ferrous parts can occur. This test indicates how well inhibited mineral oils aid in preventing this type of rusting. This test method is also used for testing...

ASTM D1748-24 - Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet
November 1, 2024 - ASTM International

1.1 This test method covers the evaluation of the rust-preventive properties of metal preservatives under conditions of high humidity. 1.2 The values stated in SI units are to be regarded as the standard except where the test apparatus or consumable parts are only available in other units....

ASTM A513/A513M-25 - Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
May 1, 2025 - ASTM International

This specification covers round, square, rectangular, and special shape electric-resistance-welded carbon and alloy steel mechanical tubing produced by hot- or cold-rolling. The types of tubing covered here are: Type 1a, as-welded from hot-rolled steel (with mill scale); Type 1b, as-welded from...

ASTM D1014-25 - Standard Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates
February 1, 2025 - ASTM International

4.1 The procedures described in this practice are intended to aid in evaluating the performance of coatings on various metal panels including either new or rusted steel. 4.2 The relative durability of paints in outdoor exposures can be very different depending on the location of the exposure...

ASTM D6294/D6294M-13(2024) - Standard Test Method for Corrosion Resistance of Ferrous Metal Fastener Assemblies Used in Roofing and Waterproofing
November 1, 2024 - ASTM International

1.1 This test method covers components of ferrous metal fastener assemblies, excluding those of stainless steel, such as fasteners, stress plates, and batten bars used in low-slope roofing and waterproofing, to a sulfurous acid environment. This test method evaluates relative corrosion resistance...

ASTM F2162-01(2025) - Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type
January 1, 2025 - ASTM International

This specification covers the requirements for standard-type needle roller bearings with drawn outer rings, full complement, without inner rings, and with either open (Type B) or closed ends (Type M). Materials covered by this specification are needle rollers which shall be manufactured from steel,...

Advertisement