1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...
1.1 This practice describes a methodology for designing and installing conventional (screened and filter-packed) groundwater monitoring wells suitable for formations ranging from unconsolidated aquifers (that is, sands and gravels) to granular materials having grain-size distributions with...
1.1 This practice is based on recognized methods by which direct push monitoring wells may be designed and installed for the purpose of detecting the presence or absence of a contaminant, and collecting representative groundwater quality data. The design standards and installation procedures herein...
1.1 This test method covers the determination of per- and polyfluoroalkyl substances (PFAS) in soil/biosolid matrices by solvent extraction, filtering, separation using liquid chromatography (LC), and detection with tandem mass spectrometry (MS/MS). These analytes are extracted from...
5.1 Impact Value, as determined using the standard 4.5 kg (10 lbm) hammer, has direct application to design and construction of pavements and a general application to earthworks compaction control and evaluation of strength characteristics of a wide range of materials, such as soils, soil...
5.1 This test method has been developed by the U.S. EPA Region 5 Chicago Regional Laboratory (CRL). 5.2 PFAS are widely used in various industrial and commercial products; they are persistent, bio-accumulative, and ubiquitous in the environment. PFAS have been reported to exhibit developmental...
1.1 This test method covers the determination of the sand content of bentonitic slurries used in slurry construction techniques. This test method has been modified from API Recommended Practice?13B. 1.2 All observed and calculated values shall conform to the guidelines for significant digits...
4.1 Damage to a pipe coating is almost unavoidable during transportation and construction. Breaks or holidays in pipe coatings may expose the pipe to possible corrosion since, after a pipe has been installed underground, the surrounding earth will be moisture-bearing and will constitute an...
1.1 This Standard is intended to be read together with the Standard for Rotating Electrical Machines - General Requirements, UL 1004-1 and all other applicable UL 1004 series (Standard for Impedance Protected Motors, UL 1004-2, Standard for Thermally Protected Motors, UL 1004-3, Standard for...
5.1 Stress may be applied intentionally through a heat treatment or tempering process to increase mechanical strength and improve safety characteristics of glass sheets. The process itself makes it practically impossible to achieve a homogenous residual stress profile over a full glass panel. These...
5.1 Stress may be applied intentionally through a heat treatment or tempering process to increase mechanical strength and improve safety characteristics of glass sheets. The process itself makes it practically impossible to achieve a homogenous residual stress profile over a full glass panel. These...
5.1 Stress may be applied intentionally through a heat treatment or tempering process to increase mechanical strength and improve safety characteristics of glass sheets. The process itself makes it practically impossible to achieve a homogenous residual stress profile over a full glass panel. These...
Introduction The definition of filtration contains the word medium. This medium can be granular (e.g., sand or coal) or it can be composed of synthetic material (membranes). This book focuses on the evaluation of granular filter media. By definition, filtration does not seem...
This Standard contains minimum requirements for residential wastewater treatment systems having rated treatment capacities of 1514 L/d (400 gal/d) to 5678 L/d (1500 gal/d) that are designed to provide reduction of nitrogen in residential wastewater. Management methods for the treated effluent...
This standard describes gravel, high-density gravel, silica sand, high-density media, anthracite filter materials, and the placement of the materials in filters for water supply service application. ANSI/AWWA B604, Standard for Granular Activated Carbon, addresses use of GAC as...
This document specifies a method for the detection, semi-quantitative and quantitative (MPN) enumeration of thermotolerant Campylobacter species. The method can be applied to all kinds of waters including: drinking water, ground water and well water, fresh, brackish and saline surface water,...
5.1 This test method has been developed by the U.S. EPA Region 5 Chicago Regional Laboratory (CRL). 5.2 TTPC may be used in various industrial and commercial products for use as a biocide. Products containing TTPC have been approved for controlling algal, bacterial, and fungal slimes in industrial...
Narrow Your Results