loading
ASTM D5114/D5114M-90(2026) - Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
July 15, 2026 - ASTM International

1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 μm (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables. 1.2 This test method does...

ASTM E2470-26 - Standard Specification for Polyester Grade Ethylene Glycol
July 1, 2026 - ASTM International

This specification covers polyester grade ethylene glycol. Sampled specimens shall undergo tests, for which the following chemical and physical requirements should be met: acidity (as acetic acid); aldehydes (acetaldehyde) content; appearance; chloride content; color (Pt-Co scale); glycols...

ASTM D1403-26 - Standard Test Methods for Cone Penetration of Lubricating Grease Using One-Quarter and One-Half Scale Cone Equipment
April 1, 2026 - ASTM International

1.1 These test methods cover two procedures for measuring the consistency of small samples of lubricating greases by penetration of a 1/4-scale cone or a 1/2-scale cone. These test methods include procedures for the measurement of unworked and worked penetrations. 1.2 Unworked...

ASTM E2425-21(2026) - Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers
July 1, 2026 - ASTM International

1.1 This test method describes the performance confirmation or measurement of conformance for the loss modulus scale of a commercial or custom-built dynamic mechanical analyzer (DMA) at 21 °C using ultra-high molecular weight polyethylene as a reference material. 1.2 The values stated in SI...

ASTM E3301-26 - Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers Using Thermal Lag
July 1, 2026 - ASTM International

5.1 Dynamic mechanical analysis monitors changes in the viscoelastic properties (that is, storage modulus, loss modulus, tangent angle delta) of a material as a function of temperature and frequency, providing a means to quantify these changes. In many cases, the value to be assigned is the...

ASTM D2700-26b - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25?% v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that...

ASTM D2699-26 - Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
July 1, 2026 - ASTM International

1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Research O.N., including fuels that contain up to 25?% v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that are...

ASTM D3321-26 - Standard Test Method for Use of Handheld Refractometers for the Determination of the Freeze Point and % Glycol of Aqueous Engine Coolants
June 1, 2026 - ASTM International

1.1 This test method covers the use of portable refractometers for determining the approximate freezing point and % glycol provided by ethylene and propylene glycol-based coolants used in cooling systems. Note 1: This test method does not cover scales for other fluids that may be present on...

ASTM D1238-26 - Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
July 15, 2026 - ASTM International

5.1 This test method is particularly useful for quality control tests on thermoplastics. 5.2 The data produced by this test method serves to indicate the uniformity of the flow rate of the polymer as made by an individual process. It is not to be used as an indication of uniformity of other...

ASTM D4986-26 - Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials
July 1, 2026 - ASTM International

1.1 This fire-test-response standard contains a test method for small-scale laboratory procedures to be used to determine the relative rate of burning and the extent and time of burning of horizontally oriented cellular polymeric materials having a density less than 250 kg/m3. 1.2 The...

ASTM D6299-26a - Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
July 1, 2026 - ASTM International

1.1 This practice covers information for the design and operation of a program to monitor and control ongoing stability and precision and bias performance of selected analytical measurement systems using a collection of generally accepted statistical quality control (SQC) procedures and tools. Note...

ASTM D613-26 - Standard Test Method for Cetane Number of Diesel Fuel Oil
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the rating of diesel fuel oil in terms of an arbitrary scale of cetane numbers using a standard single cylinder, four-stroke cycle, variable compression ratio, indirect injected diesel engine. 1.2 The cetane number scale covers the...

ASTM C1824-16(2026) - Standard Test Method for Full Scale Bending Test of Spun Prestressed Concrete Bases for Tapered Steel Lighting Poles
June 1, 2026 - ASTM International

5.1 This test method is intended to provide the user with acceptable apparatus requirements and a prescribed procedure to determine the bending moment capacity of spun pre-stressed concrete bases for use with tapered steel poles. 5.2 The results of this test method are used as a basis for...

ASTM E3001-20(2026) - Standard Practice for Workforce Education in Nanotechnology Characterization
June 1, 2026 - ASTM International

1.1 This practice describes a procedure to provide the basic education of characterization methods for nanometer-scale materials, to be taught at an undergraduate college level. This education should be broad and include a suite of characterization methods to prepare an individual to work in...

ASTM E800-26 - Standard Guide for Measurement of Gases Present or Generated During Fires
June 1, 2026 - ASTM International

1.1 Analytical methods for the measurement of carbon monoxide, carbon dioxide, oxygen, nitrogen oxides, sulfur oxides, carbonyl sulfide, hydrogen halides, hydrogen cyanide, aldehydes, and hydrocarbons are described, along with sampling considerations. Many of these gases may be present in any fire...

ASTM D4328-18(2026) - Standard Practice for Calculation of Supersaturation of Barium Sulfate, Strontium Sulfate, and Calcium Sulfate Dihydrate (Gypsum) in Brackish Water, Seawater, and Brines
May 1, 2026 - ASTM International

4.1 This practice covers the mathematical calculation of the supersaturation of three principal sulfate scaling compounds found in industrial operations. Application of this standard practice to the prediction of scale formation in a given system, however, requires experience. The...

ASTM E3248-26 - Standard Guide for Non-Aqueous Phase Liquid (NAPL) Mobility and Migration in Sediment—Conceptual Models for NAPL Emplacement and Influence on NAPL Movement
May 15, 2026 - ASTM International

1.1 This guide is designed for application at a wide range of sediment sites where non-aqueous phase liquid (NAPL) is present or suspected to be present. This guide describes emplacement mechanisms that can result in NAPL presence within sediment and how the characteristics of the sediment, aquatic...

ASTM D2700-26a - Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
June 1, 2026 - ASTM International

1.1 This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25?% v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that...

ASTM D4970/D4970M-22(2026) - Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Martindale Tester
July 1, 2026 - ASTM International

5.1 Acceptance Testing-This method of testing fabrics resistance to pilling is not recommended for acceptance testing. If it is used for acceptance testing, it should be used with caution because interlaboratory data are not available. In some cases the purchaser or supplier may have to test a...

ASTM D6400-26 - Standard Specification for Labeling of Plastics Designed to be Aerobically Composted in Municipal or Industrial Facilities
June 1, 2026 - ASTM International

1.1 This specification covers plastics and products made from plastics that are designed to be composted under aerobic conditions in municipal and industrial aerobic composting facilities, where thermophilic conditions are achieved. 1.2 This specification is intended to establish the requirements...

Advertisement