loading
ASTM E2253-26 - Standard Test Method for Temperature and Enthalpy Measurement Validation of Differential Scanning Calorimeters
July 1, 2026 - ASTM International

1.1 This test method provides procedures for validating temperature and enthalpy measurements of differential scanning calorimeters (DSC) and analytical methods based upon the measurement of temperature or enthalpy (or heat), or both, by DSC. Performance parameters determined include...

ASTM E1001-21(2026) - Standard Practice for Detection and Evaluation of Discontinuities by the Immersed Pulse-Echo Ultrasonic Method Using Longitudinal Waves
July 1, 2026 - ASTM International

6.1 This practice provides guidelines for the application of immersed longitudinal wave examination to the detection and quantitative evaluation of discontinuities in materials. 6.2 Although not all requirements of this practice can be applied universally to all examination situations and...

ASTM E2550-26 - Standard Test Method for Thermal Stability by Thermogravimetry
July 1, 2026 - ASTM International

5.1 Thermogravimetry provides a rapid method for determining the thermal decomposition and reaction mass change of a material. 5.2 This test method is useful in detecting potentially hazardous reactions and in estimating the temperatures at which these reactions occur. This test method is...

ASTM D7919-26 - Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes
June 1, 2026 - ASTM International

1.1 This guide pertains to removal and analysis techniques to extract debris captured by in-service lubricant and hydraulic filters and to analyze the debris removed. 1.2 This guide suggests techniques to remove, collect and analyze debris from filters in support of machinery health condition...

ASTM E1441-19(2026) - Standard Guide for Computed Tomography (CT)
May 1, 2026 - ASTM International

1.1 CT is a radiographic examination technique that generates digital images in three dimensions of an object, including the interior structure. Because of the relatively good penetrability of X rays, CT permits the nondestructive physical and, to a limited extent, chemical characterization of the...

ASTM E2964-26 - Standard Test Method for Measurement of the Normalized Insertion Loss of Doors
May 15, 2026 - ASTM International

5.1 This standard provides a method for testing the apparent sound insulating properties of doors in the field originally proposed by Morin (1). This allows doors to be evaluated with a result that has been found to be similar to the transmission loss. 5.2 The results of this measurement are the...

ASTM E2090-12(2026) - Standard Test Method for Size-Differentiated Counting of Particles and Fibers Released from Cleanroom Wipers Using Optical and Scanning Electron Microscopy
May 1, 2026 - ASTM International

5.1 This test method provides for accurate and reproducible enumeration of particles and fibers released from a wiper immersed in a cleaning solution with moderate mechanical stress applied. When performed correctly, this counting test method is sensitive enough to quantify very low levels of total...

ASTM ASTM51631-26 - Standard Practice for Use of Calorimetric Dosimetry Systems for Dose Measurements and Routine Dosimetry System Calibration in Electron Beams
May 1, 2026 - ASTM International

1.1 This practice covers the preparation and use of semi-adiabatic calorimetric dosimetry systems for measurement of absorbed dose and for calibration of routine dosimetry systems when irradiated with electrons for radiation processing applications. The calorimeters are either transported by a...

ASTM D8363-20(2026) - Standard Test Method for Rubber—Stress Relaxation in Tension Under Non-Isothermal Conditions
April 1, 2026 - ASTM International

5.1 Non-isothermal stress relaxation, also known as temperature scanning stress relaxation, performed at a specific heating rate, delivers a set of parameters useful to specify the properties of thermo-plastic elastomers. It can also characterize the deterioration of the cross-linked rubber...

ASTM E2700-26 - Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays
January 1, 2026 - ASTM International

1.1 This practice covers ultrasonic techniques for examining welds using phased array ultrasonic methods (see Note 1 and Note 2). 1.2 This practice uses angle beams, either in S-scan or E-scan modes, primarily for butt welds and tee welds. Alternative welding techniques, such as solid...

ASTM E2069-25 - Standard Test Method for Temperature Calibration of Differential Scanning Calorimeters on Cooling
December 1, 2025 - ASTM International

1.1 This test method describes the temperature calibration of differential scanning calorimeters (DSCs) on cooling using the difference between transition temperatures upon heating and cooling in the temperature range of 65 °C to 420 °C. Within this temperature range, an offset in the...

ASTM E2375-26a - Standard Practice for Ultrasonic Testing of Wrought Products
March 15, 2026 - ASTM International

1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...

ASTM E3-26 - Standard Guide for Preparation of Metallographic Specimens
February 15, 2026 - ASTM International

1.1 The primary objective of metallographic examinations is to reveal the constituents and structure of metals and their alloys by means of a light optical or scanning electron microscope. In special cases, the objective of the examination may require the development of less detail than in...

ASTM E3345-26 - Standard Practice for Opinions on the Interpretation of Primer Gunshot Residue (pGSR) Analysis by Scanning Electron Microscopy/Energy Dispersive X-Ray Spectrometry (SEM/EDS)
February 1, 2026 - ASTM International

4.1 This practice is of use to persons who present opinions regarding primer gunshot residue analysis results and to provide guidance to those in the legal community who use such opinions. 4.2 This practice is intended to be used in conjunction with Practice E620, Test Method E1588, and Guide E3309.

ASTM E3497-26 - Standard Practice for Collection of Primer Gunshot Residue (pGSR) Particles from Clothing, Vehicles, and Other Inanimate Objects using Scanning Electron Microscopy (SEM) Stubs
February 1, 2026 - ASTM International

5.1 pGSR originates from the explosion of the priming mixture following ignition during the firearm discharge process. After a firearm has been discharged, residue can be found on exposed surfaces in the vicinity of the fired weapon (4, 5). 5.2 The most common reason for pGSR examination is to...

ASTM E928-25 - Standard Test Method for Purity by Differential Scanning Calorimetry
September 1, 2025 - ASTM International

1.1 This test method describes the determination of purity of materials greater than 98.5 mol % purity using differential scanning calorimetry and the van't Hoff equation. 1.2 This test method is applicable to thermally stable compounds with well-defined melting temperatures (that is, not...

ASTM D5028-25 - Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis
December 1, 2025 - ASTM International

1.1 This test method covers determination of curing parameters of pultrusions resins by differential scanning calorimetry. 1.2 This test method is applicable to pultrusion resin solutions with adequate initiator(s). 1.3 The normal operating temperature range is from 0 to 200°C. Note 1: Resin...

ASTM E494-20(2025) - Standard Practice for Measuring Ultrasonic Velocity in Materials by Comparative Pulse-Echo Method
December 1, 2025 - ASTM International

This practice covers a test procedure for measuring ultrasonic velocities in materials with conventional ultrasonic pulse echo flaw detection equipment in which results are displayed in an A-scan display, and describes a method whereby unknown ultrasonic velocities in a material sample are...

ASTM E2785-26 - Standard Practice for Exposure of Firestop Materials to Various Specified Enhanced Environmental Factors
January 1, 2026 - ASTM International

5.1 This practice is intended to evaluate the material performance after exposure to specified environmental factors. It is understood that these performance values are dependent upon these specified exposure periods and intensities of environmental factors. Other values are possible if the...

ASTM E2375-26 - Standard Practice for Ultrasonic Testing of Wrought Products
January 1, 2026 - ASTM International

1.1 Purpose-This practice covers the minimum requirements for ultrasonic examination of wrought products. Note 1: This practice was adopted to replace MIL-STD-2154, 30 Sept. 1982. This practice is intended to be used for the same applications as the document which it replaced. Users should...

Advertisement