loading
ASTM F1488-26a - Standard Specification for Coextruded Composite Pipe
August 1, 2026 - ASTM International

This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40...

ASTM C336-26 - Standard Test Method for Annealing Point and Strain Point of Glass by Fiber Elongation
July 1, 2026 - ASTM International

4.1 This test method provides data useful for (1) estimating stress release, (2) the development of proper annealing schedules, and (3) estimating setting points for seals. Accordingly, its usage is widespread throughout manufacturing, research, and development. It can be utilized for...

ASTM B673-26 - Standard Specification for Nickel-Iron-Chromium-Molybdenum-Nitrogen Alloy Welded Pipe
July 1, 2026 - ASTM International

1.1 This specification covers UNS N08034, UNS N08935, and UNS N08354 welded pipe for general corrosion applications. 1.2 This specification covers pipe sizes in schedules shown in Table 1. 1.3 ASTM International has adopted definitions whereby some grades, such as UNS N08904, previously in...

ASTM C901-26 - Standard Guide for Design and Installation of Prefabricated Masonry Elements
June 1, 2026 - ASTM International

4.1 This guide is intended to provide information and guidance for designers, specifiers, manufacturers, contractors and users that are considering the use of prefabricated masonry elements. This guide identifies situations when prefabrication could be considered where other prefabricated systems...

ASTM F1898-26 - Standard Specification for Helmets for Non-Motorized Wheeled Vehicles Used by Infants and Toddlers
May 1, 2026 - ASTM International

This specification covers the performance requirements for helmets manufactured for use by infants and toddlers as passengers or operators of non-motorized wheeled vehicles. The performance requirements to which the helmets shall conform include those for headforms, peripheral vision, retention...

ASTM E1419/E1419M-26 - Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels Using Acoustic Emission
May 1, 2026 - ASTM International

5.1 Because of safety considerations, regulatory agencies (for example, U.S. Department of Transportation) require periodic examinations of vessels used in transportation of industrial gases (see Section 49, Code of Federal Regulations). The AE examination has become accepted as an alternative to...

ASTM F1488-26 - Standard Specification for Coextruded Composite Pipe
February 1, 2026 - ASTM International

This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40...

ASTM D6956-17(2026) - Standard Guide for Demonstrating and Assessing Whether a Chemical Analytical Measurement System Provides Analytical Results Consistent with Their Intended Use
January 1, 2026 - ASTM International

4.1 This guide is intended for use by both generators and users of analytical results. It is intended to promote consistent demonstration and documentation of the quality of the measurement results and facilitate determination of the validity of measurements for their intended use. 4.2 This guide...

ASTM E1699-26 - Standard Practice for Performing Value Engineering (VE)/Value Analysis (VA) of Projects, Products and Processes
January 1, 2026 - ASTM International

5.1 Use of this practice may increase performance in one or more areas including: cost control; resource allocation; schedule management; quality control; risk management; or safety. Perform VE/VA as early as possible in the life cycle of the focus of study, and anytime conditions change, to...

ASTM G228-26 - Standard Practice for Conducting a 5-year Review of a Committee G03 Standard
January 1, 2026 - ASTM International

5.1 It is the intention of this practice, in addition to the Form and Style for ASTM Standards, to assist persons revising standards in Committee G03 to ensure that all required elements are included and that the revised document is presented in the most user-friendly manner possible. 5.2 This...

ASTM F1488-25a - Standard Specification for Coextruded Composite Pipe
December 1, 2025 - ASTM International

This specification covers coextruded composite pipe, produced by a coextrusion die system, in which the concentric layers are formed and combined before exiting the die. Coextruded composite pipe conforming to the requirements prescribed are used for different applications: IPS Schedule 40...

ASTM D6442-06(2026) - Standard Test Method for Determination of Copper Release Rate From Antifouling Coatings in Substitute Ocean Water
January 1, 2026 - ASTM International

4.1 This test method is designed to provide a laboratory procedure to quantify and characterize the release rates of copper from antifouling coatings in substitute ocean water over a period of immersion under specified laboratory conditions of constant temperature, pH, salinity, and low copper...

ASTM D6903-07(2026) - Standard Test Method for Determination of Organic Biocide Release Rate From Antifouling Coatings in Substitute Ocean Water
January 1, 2026 - ASTM International

4.1 This test method is designed to provide a laboratory procedure to quantify and characterize changes in the release rate of organic biocide from antifouling coatings that occur during a period of immersion under specified laboratory conditions of constant temperature, pH, salinity, and...

ASTM C612-25 - Standard Specification for Mineral Fiber Block and Board Thermal Insulation
November 15, 2025 - ASTM International

This specification covers mineral fiber block and board thermal insulation. Mineral fiber board insulation covered by this specification shall be classified into types and categories; category 1 - no compressive resistance properties are required, category 2 - minimum compressive resistance...

ASTM F480-25 - Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
December 1, 2025 - ASTM International

1.1 This specification covers water well casing pipe and couplings made from thermoplastic materials in standard dimension ratios (SDR), SCH 40 and SCH 80. 1.2 Specifications are provided for the application of these materials to water well and ground water monitoring applications. Flush threaded...

ASTM F3803-26 - Standard Guide for Applying Goods Movement Process Codes in Common Approaches to Transport Management
January 1, 2026 - ASTM International

5.1 This section elaborates how the GMPC may be used in the context of the two main approaches to managing the execution of transportation mentioned in 4.8. These elaborations do not go into every possible detail of these approaches. The purpose of the elaborations is to provide an outline of the...

ASTM F3804-26 - Standard Practice for Applying a Goods Movement Process Code as Suffix to the ISO Transport Unit Identifier
January 1, 2026 - ASTM International

5.1 This section elaborates how the GMPC may be used in the context of the two main approaches to managing the execution of transportation mentioned in 5.2. These elaborations do not go into every possible detail of these approaches. The purpose of the elaborations is to provide an outline of the...

ASTM C1787-25 - Standard Specification for Installation of Non Metallic Plaster Bases (Lath) Used with Portland Cement Based Plaster
October 1, 2025 - ASTM International

This specification describes the minimum requirements for the installation of non-metallic plaster bases used with portland cement-based plaster in vertical wall applications. In cases where a fire resistance rating is required for plastered assemblies and constructions, the construction details...

ASTM C113-14(2025) - Standard Test Method for Reheat Change of Refractory Brick
August 1, 2025 - ASTM International

3.1 Refractory brick and shapes of different compositions exhibit unique permanent linear changes after heating or reheating. This test method provides a standard procedure for heating various classes of refractories with appropriate heating schedules. 3.2 Linear reheat changes obtained by...

ASTM F1492-25 - Standard Specification for Helmets Used in Skateboarding and Trick Roller Skating
September 1, 2025 - ASTM International

These specifications cover the design and performance requirements, and associated test procedures for helmets used in the activities of skateboarding and trick roller skating. When tested, the helmets shall meet specified requirements for the peak acceleration and time duration, headforms and...

Advertisement