1.1 This document describes the appearance of a radiographic image where fundamental components of image quality are changed, that is, variables such as whether an X-ray or gamma ray source was used, the characteristics of the radiographic film (gradient, granularity, and developing conditions) and...
4.1 A key consideration with any radiographic system is its contrast resolution and spatial resolution capability (that is, sensitivity). The degree of obtainable sensitivity with a given system is dependent upon several radiographic parameters such as source energy level, film system class, type...
1.1 This specification covers the aesthetic quality requirements for decorative enamels applied to flat glass for use in building glazing. 1.2 This specification covers the requirements for flat glass, with either organic or ceramic enamels applied. 1.2.1 Glass may be annealed, heat-strengthened,..
5.1 Many sliding systems exhibit intermittent high friction force excursions compared to competing tribosystems. However, where friction forces or friction coefficients are averaged, the test data may show that the two systems have the same friction characteristics, when in fact they were not the...
4.1 This guide covers types of materials to be examined, neutron radiographic examination techniques, neutron production and collimation methods, radiographic film, and converter screen selection. Within the present state of the neutron radiographic art, these practices are generally...
1.1 This practice covers the evaluation of the relative resistance of printed matter to liquid chemicals, as evidenced by lack of discoloration, bleeding, or loss of gloss. 1.2 This practice utilizes a sandwich procedure similar in principle to ISO/TC 130 N 589. Spotting or immersion procedures are...
1.1 This test method defines an empirical technique for the measurement of the effective collimation ratio, L/D, of neutron radiography beams. The technique is based upon analysis of a neutron radiographic image and is independent of measurements and calculations based on physical dimensions of the...
This specification covers woven or welded galvanized steel wire fabric commercially known as hardware cloth. It is customarily used for window and screen door guards, tree guards, industrial machine guards, sand screens, and grain bins. It serves as a protective screen against...
3.1 This test method determines the size distribution of coke for conformance to specifications of percentages retained on designated screen sizes.
5.1 The transmission of power in many automotive and industrial applications is accomplished through the use of geared systems. At higher operating speeds it is well known that the lubricant/additive system can be a significant factor in preventing scuffing (adhesive wear) damage to gears. This...
This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of heavy steel forgings by the straight and angle-beam techniques. An ultrasonic, pulsed, reflection type of instrument shall be used and shall provide linear presentation for at least 75% of the...
1.1 This practice covers a short-term testing method to screen the subcutaneous tissue reaction to implant candidate materials in small laboratory animals. The material may be dense or porous. This method may not work for absorbable materials, depending on the absorption kinetics. The tissue...
This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method...
This specification covers standard methods for sampling and testing of various ferroalloys for size analysis. Ferroalloys are classified into lump and crushed or plates sizes. The small-sized samples subject to screen testing shall be taken from the lot sample by riffling, and larger sized...
5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...
5.1 Corrosion inhibitors continue to play a key role in controlling internal corrosion associated with oil and gas production and transportation. This results primarily from the industry's extensive use of carbon and low alloy steels, which, for many applications, are economic materials of...
1.1 This specification covers the requirements for chemically strengthened glass products that are used in general building construction, transportation, solar energy, and other electronic applications, such as PC screens, notebooks, tablets, smart phones, and e-readers, as well as copy...
5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...
1.1 This specification covers indoor ballistic test range requirements for small arms and fragmentation testing of the following ballistic-resistant items: soft body armor, hard armor plates, body armor accessories, shields, and helmets. The specification includes requirements for range geometry...
4.1 The application of direct air-rotary drilling to geoenvironmental exploration may involve sampling, coring, in situ or pore-fluid testing, installation of casing for subsequent drilling activities in unconsolidated or consolidated materials, and for installation of subsurface water-quality...
Narrow Your Results