This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and commercial,...
4.1 This test method provides data useful for (1) estimating stress release, (2) the development of proper annealing schedules, and (3) estimating setting points for seals. Accordingly, its usage is widespread throughout manufacturing, research, and development. It can be utilized for...
1.1 This specification covers coextruded composite pipe, intended for non-pressure gravity flow drain waste or vent (DWV) service, or plastic underdrain service, or electrical or comunications conduit service produced by a coextrusion die system, in which the concentric layers are formed and...
4.1 Determination of the hydro-thermal area stability of Wet Blue provides information concerning the efficacy of the tanning process as well as the adequacy of the Wet Blue for intended end use applications where area stability is a particular requirement. Relative area stability of chrome-tanned...
1.1 This test method covers procedures for testing the durability of preassembled, permanently sealed vacuum insulating glass (VIG) units. 1.2 This test method is applicable only to VIG units that are constructed with flat glass lites (glass panes). 1.3 This test method is applicable to...
1.1 This consumer safety specification covers the performance requirements and test methods to ensure the safety of chests. 1.2 This consumer safety specification is intended to minimize the incidents and injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of...
This specification provides chemical and physical requirements for nuclear-grade gadolinium oxide powder intended for subsequent processing and use in nuclear fuel applications. Chemical requirements of the specification include loss-on-ignition, gadolinium oxide concentration, and impurity content...
1.1 This specification covers preformed dense elastomeric compression gaskets and accessories for use in sealing and glazing applications. These materials are generally used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building...
5.1 This guide is intended to provide machinery maintenance and monitoring personnel with a guideline for performing filter debris analysis as a means to determine machine condition. Correlating the filter contaminants to 'normal' and 'abnormal' lube system operation provides early indication of a...
1.1 This test method covers the use of a sealed cavity rotorless oscillating shear rheometer for the measurement of the softening effects of rising sinusoidal strain when applied to an unvulcanized rubber compound containing significant amounts of colloidal fillers (such as silica or carbon...
4.1 The design and operation of a self-contained irradiator should ensure that reproducible absorbed doses are obtained when the same irradiation parameters are used. Dosimetry is performed to determine the relationship between the irradiation parameters and the absorbed dose. 4.1.1 For most...
5.1 Due to hydraulic pressure that may be present on some applications, engineers need to understand the capability of these products to resist this pressure. This test allows engineers to compare products and verify pullout strength. 5.2 Hydraulic pullout resistance is a function of locking...
1.1 This standard describes terms and definitions and descriptions of terms used in test methods, specifications, guides, and practices (related to building seals and sealants) consistent with the scope and areas of interest of ASTM Committee C24. 1.2 Definitions and descriptions of terms...
4.1 In this test method, a compacted sample is vacuum sealed inside a plastic bag. The density of the sample, SG1, is calculated using a water displacement method, with the sample sealed. With the sample still in water, the bag is cut open. Since the sample is under vacuum and the air...
1.1 This test method covers the measurement of the transmission of a gas through plastic membranes, sheeting, films, and fabric materials using a static sealed diffusion chamber. The test method monitors gas diffusion across a film membrane and provides measurements of (1) gas concentrations...
5.1 Analyzing in-service lubricating oil and hydraulic fluid samples is crucial for assessing the condition of both the fluid and the equipment. The results of the fluid analysis guide the planning of any necessary corrective maintenance activities. 5.2 The objective of this guide is to support...
1.1 This practice covers the preparation of an equilibrium gas sample of live crude oil, condensate, or liquid petroleum products, using a Practice D8009 manual piston cylinder (MPC) as a vapor tight expansion chamber to generate an equilibrium vapor/liquid pair at a known temperature and...
5.1 When a constant strain is imposed on rubber, the force necessary to maintain that strain is not constant but decreases with time; this phenomenon is called force decay (stress relaxation). Conversely, when rubber is subjected to a constant stress, an increase in the deformation takes place in...