loading
ASTM F3214-26 - Standard Practice for Characterization of Fire Properties of Seating, Upholstery, and Padding Materials for Vehicles Associated with Amusement Rides and Devices
March 1, 2026 - ASTM International

4.1 This practice requires that seating, upholstery, and padding materials used for vehicles associated with amusement rides and devices exhibit adequate smoldering ignition properties. 4.1.1 Noncombustible materials are permitted to be used as seating, upholstery, and padding...

ASTM F2836-26 - Standard Practice for Gasket Constants for Bolted Joint Design
June 1, 2026 - ASTM International

5.1 This practice determines the room temperature gasket constants Gb and a for initial seating and Gs for operating conditions as related to the tightness behavior of pressurized bolted flanged connections. These constants are used in determining the design bolt load for gasketed bolted...

ASTM F3174/F3174M-26 - Standard Specification for Establishing Operating Limitations and Information for Aeroplanes
May 1, 2026 - ASTM International

1.1 This specification covers airworthiness requirements for establishing general limitations and information to be contained in the aeroplane flight manual. This specification specifies what information shall be provided and does not state how such information shall be presented unless this is...

ASTM F3310-26 - Standard Specification for Non-Essential Ice Detectors for Aircraft
February 1, 2026 - ASTM International

1.1 This specification covers international standards for non-essential ice detection system aspects of airworthiness and design for aeroplanes. 1.2 The term "aeroplane" is utilized in this specification as it was originally conceived for normal category fixed wing aircraft with a certified maximum...

ASTM E2280-25a - Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
August 15, 2025 - ASTM International

4.1 This guide is intended for use by those undertaking the development of fire hazard assessments for upholstered seating furniture in health care occupancies. 4.2 As a guide this document provides information on an approach to development of a fire hazard assessment, but fixed procedures...

ASTM E2280-25 - Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
June 1, 2025 - ASTM International

4.1 This guide is intended for use by those undertaking the development of fire hazard assessments for upholstered seating furniture in health care occupancies. 4.2 As a guide this document provides information on an approach to development of a fire hazard assessment, but fixed procedures...

ASTM F1235-25 - Standard Consumer Safety Specification for Portable Hook-On Chairs
November 15, 2025 - ASTM International

1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair. 1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of...

ASTM F1957-24 - Standard Test Method for Composite Foam Hardness-Durometer Hardness
November 1, 2024 - ASTM International

1.1 This test method describes a type of composite foam hardness measurement device known as durometer: Type CF. The procedure for determining indentation hardness of substances comprised of two or more elastomeric materials, one of which is a foam or foam like material. These are classified as...

ASTM F2836-18(2024) - Standard Practice for Gasket Constants for Bolted Joint Design
September 1, 2024 - ASTM International

5.1 This practice determines the room temperature gasket constants Gb and a for initial seating and Gs for operating conditions as related to the tightness behavior of pressurized bolted flanged connections. These constants are used in determining the design bolt load for gasketed bolted...

ASTM F3727-24 - Standard Test Method for Fire Testing of Vandalized Upholstered Furniture
October 1, 2024 - ASTM International

5.1 This test method provides a means to measure a variety of fire-test-response characteristics resulting from burning a specimen of upholstered furniture, both as manufactured and after vandalization to expose the padding. The upholstered furniture specimen (see Section 6) is allowed to burn...

ASTM F3214-23 - Standard Practice for Characterization of Fire Properties of Seating, Upholstery, and Padding Materials for Vehicles Associated with Amusement Rides and Devices
March 1, 2023 - ASTM International

4.1 This practice requires that seating, upholstery, and padding materials used for vehicles associated with amusement rides and devices exhibit adequate smoldering ignition properties. 4.1.1 Noncombustible materials are permitted to be used as seating, upholstery, and padding...

ASTM F3082/F3082M-23a - Standard Specification for Weights and Centers of Gravity of Aircraft
September 1, 2023 - ASTM International

1.1 This specification establishes the airworthiness design standards associated with aeroplane weight and center of gravity. 1.2 The term "aeroplane" is utilized in this specification as it was originally conceived for normal category fixed wing aircraft with a maximum certificated weight of 19...

UL 962A - Furniture Power Distribution Units
July 13, 2023 - ULSE

1.1 These requirements cover indoor use cord and plug connected of permanently connected, furniture power distribution units (FPDU) rated 250 V AC or less and 20 Amperes or less. An FPDU may provide one or more receptacle outlets, inclusive of one current tap integral to the attachment plug, if...

J1454_202302 - Dynamic Durability Testing of Seat Cushions for Off-Road Work Machines
February 14, 2023 - SAE International

This SAE Standard describes a laboratory test procedure for comparatively evaluating the durability and fatigue life qualities of a complete seat cushion by submitting the seating surface of the cushion to repetitive compressive and rotational loading with a simulated human buttocks.

ASTM F3082/F3082M-23 - Standard Specification for Weights and Centers of Gravity of Aircraft
February 15, 2023 - ASTM International

1.1 This specification establishes the airworthiness design standards associated with aeroplane weight and center of gravity. 1.2 The term "aeroplane" is utilized in this specification as it was originally conceived for normal category fixed wing aircraft with a maximum certificated weight of 19...

ASTM F3601-23 - Standard Practice for Structural Finite Element Model Verification and Validation
March 1, 2023 - ASTM International

1.1 This practice provides guidance for verification and validation of structural finite element models (FEMs) that are used to support showings of compliance with Civil Aviation Authority (CAA) regulations. This encompasses FEM predictions of internal loads, displacements, strains, stresses,...

AS8049/1B - Performance Standards for Side-Facing Seats in Civil Rotorcraft, Transport Aircraft, and General Aviation Aircraft
January 20, 2023 - SAE International

This SAE Aerospace Standard (AS) defines Minimum Performance Standards (MPS), qualification requirements, and minimum documentation requirements for side-facing seats in civil rotorcraft, transport aircraft, and general aviation aircraft. The goal is to achieve comfort, durability, and occupant...

J1834_202210 - Seat Belt Comfort, Fit, and Convenience - Truck and Bus
October 7, 2022 - SAE International

This SAE Recommended Practice provides design, test, and performance guidelines on the comfort, fit, and convenience for active restraint systems for heavy trucks and multipurpose passenger vehicle applications over 10000 pounds gross vehicle weight rating (GVWR). The information pertains to the...

ASTM F1166-23 - Standard Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
January 1, 2023 - ASTM International

1.1 This practice provides ergonomic design criteria from a human-machine perspective for the design and construction of maritime vessels and structures and for equipment, systems, and subsystems contained therein, including vendor-purchased hardware and software. 1.1.1 The focus of these design...

ASTM E2280-21 - Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
December 15, 2021 - ASTM International

4.1 This guide is intended for use by those undertaking the development of fire hazard assessments for upholstered seating furniture in health care occupancies. 4.2 As a guide this document provides information on an approach to development of a fire hazard assessment, but fixed procedures...

Advertisement