This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction (VIM), or...
1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory. Note 1: Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases...
5.1 This test method can be useful in characterizing and comparing shrinkage properties of both primary and secondary backing fabrics. This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between-laboratory precision are...
This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use. Materials shall be produced primarily by either electric-furnace, basic oxygen, vacuum-induction (VIM), or...
1.1 This specification describes the physical requirements for primary and secondary terrestrial nonconcentrator photovoltaic reference cells. A reference cell is defined as a device that meets the requirements of this specification and is calibrated in accordance with Test Method E1125 or...
5.1 This is intended to outline O&M issues that require discussion and mutual agreement by both the optical fiber cable owner and sewer pipeline operator. The purpose is developing sufficient written procedures and practices to allow optical fiber systems to coexist as a secondary use within...
5.1 The purpose of this guide is to provide a basic educational structure for pattern generation in nanotechnology to organizations developing or carrying out education programs for the nanotechnology workforce. This guide helps to describe the minimum knowledge base for anyone involved in...
5.1 This guide is to provide, at the undergraduate college level, a basic educational structure in the health and safety aspects of nanotechnology to organizations developing or carrying out education programs for the nanotechnology workforce. This guide helps to describe the minimum knowledge base...
5.1 Because of safety considerations, regulatory agencies (for example, U.S. Department of Transportation) require periodic examinations of vessels used in transportation of industrial gases (see Section 49, Code of Federal Regulations). The AE examination has become accepted as an alternative to...
3.1 Calcium phosphate coatings have been shown in animal and clinical studies to be biocompatible and to enhance the early attachment of bone to implant surfaces (see Refs. (1-5)). 3.2 It is believed that the form of calcium phosphate ceramic and its purity with respect to secondary...
1.1 This test method is intended for calibration and characterization of primary terrestrial photovoltaic reference cells to a desired reference spectral irradiance distribution, such as Tables G173. The recommended physical requirements for these reference cells are described in Specification...
1.1 This test method covers the procedure for a finite flash point test, within the range of -25?°C to 90?°C, of liquid wastes using an MCCCFP tester. This test method is used in the determination of flash point of liquid wastes. Note 1: The connection of tap water or a cooling device may be...
1.1 This practice covers a procedure for conducting on-site core flood tests to determine the filtration and chemical treatment requirements for subsurface injection of water. 1.2 This practice applies to water disposal, secondary recovery, and enhanced oil recovery projects and is...
5.1 Controlled stimulation, that is, the application of mechanical or thermal load, can generate AE from flawed areas of the structure. Sources may include flaw growth, oxide fracture, crack face stiction and release on load application, and crack face rubbing. 5.2 The load range above normal...
4.1 Use as an Analytical Tool-Mathematical methods provide an analytical tool to be employed for many applications related to absorbed dose determinations in radiation processing. Mathematical calculations may not be used as a substitute for routine dosimetry in some applications (for example,...
This specification deals with the general requirements that apply to rolled structural steel bars, plates, shapes, and sheet piling. The steel shall be made in an open-hearth, basic-oxygen, or electric-arc furnace followed by additional refining in a ladle metallurgy furnace, or secondary...
5.1 Presence of paper, metal, or incompatible polymer contamination in poly(ethylene terephthalate) renders the recycled polymer unfit for use in secondary product manufacturing operations. This procedure is useful for identifying different types of contamination in recycled PET flakes.
1.1 This practice describes standardized procedures for the preparation, spraying, packaging, and shipping of fresh spray polyurethane foam (SPF) insulation product samples to be tested for their emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs). These...
1.1 This practice covers the compatibility of mixtures of hydraulic fluids as defined by Specifications D6158, DIN 51524, ISO 11158, and ISO 15380. 1.2 This practice can be used to evaluate new (unused) lubricant compatibility or the effects of combining new (replacement) lubricant with in-service...
1.1 This specification describes the properties of cold, liquid-applied, single or multi-component, chemically curing, elastomeric sealants used as the secondary seal of sealed insulating glass units, hereinafter referred to as the "sealant" (see Fig. 1). These sealants are intended to be a...
Narrow Your Results