loading
RIA SERVICE ROBOTS - SERVICE ROBOTS
RIA
A description is not available for this item.
DNVGL IND SERVICE IV-7-1 - IV-Rules for the Certification and Construction Industrial Services Part 7-Offshore Substations Chapter 1-Certification and Surveys
October 1, 2013 - DNVGL

Objectives These Rules have been developed primarily to assist in the development of new installations of offshore wind farm high voltage offshore substations. These Rules are applicable to the design, fabrication, installation and commissioning of offshore renewable energy related platform...

DNVGL IND SERVICE IV-7-4 - IV-Rules for Classification and Construction Industrial Services Part 7-Offshore Substations Chapter 4-Machinery and Utility Systems
October 1, 2013 - DNVGL

referencThese Rules are applicable to machinery and equipment essential to the safety of fixed offshore substations. All machinery, electrical equipment, boilers and other pressure vessels, associated piping systems, fittings and wiring shall be of a design and construction adequate for the...

DNVGL IND SERVICE IV-7-3 - IV-Rules for Classification and Construction Industrial Services Part 7-Offshore Substations Chapter 3-General Safety
October 1, 2013 - DNVGL

This section provides general requirements for safety assessments, aiming for identifying and evaluating hazard and managing the risks.

DNVGL IND SERVICE IV-7-5 - IV-Rules for Classification and Construction Industrial Services Part 7-Offshore Substations Chapter 5-Electrical Equipment
October 1, 2013 - DNVGL

General Further equipment is required for the transmission of electrical energy that is generated by offshore wind turbines to the grid connection point at shore. This power engineering equipment usually installed on offshore substations or converter platforms, if applicable, form the basic...

DNVGL IND SERVICE IV-6-9 - IV-Rules for Classification and Construction Industrial Services Part 6-Offshore Technology Chapter 9-Guideline for Personnel Transfers by Means of Lifting Appliances
November 1, 2011 - DNVGL

Application These guidelines contain technical fundamentals on lifting appliances mainly for personnel transfer and shall apply on both ships and offshore facilities. Under the condition that the corresponding boundary conditions are observed, these Rules also shall apply for other systems.

DNVGL IND SERVICE IV-6-1 - IV-Rules for Classification and Construction Industrial Services Part 6-Offshore Technology Chapter 1-Classification, Certification and Surveys
January 1, 2007 - DNVGL

Scope of Classification New Constructions Classification covers the mobile offshore unit's or the fixed offshore installation's hull/structure and machinery including electrical installations as well as special equipment and installations as far as agreed in the building specification between the...

DNVGL IND SERVICE IV-6-6 - IV-Rules for Classification and Construction Industrial Services Part 6-Offshore Technology Chapter 6-Electrical Installations
August 1, 2007 - DNVGL

These Rules apply to electrical and electronic equipment on fixed offshore installations and mobile offshore units in accordance with Chapter 1 GL reserve the right to specify requirements additional to these Rules where they are related to new systems or installations or where they are necessary...

DNVGL IND SERVICE IV-6-3 - IV-Rules for Classification and Construction Industrial Services Part 6-Offshore Technology Chapter 3-Fixed Offshore Installations
June 1, 2007 - DNVGL

In this Chapter the requirements for the different types of fixed offshore installations are defined. Types of fixed installations The following types have to be distinguished: - installations permanently fixed by piling (pile foundation) - installations resting on the sea bed by action of gravity...

ASTM D2847-22(2026) - Standard Practice for Testing Engine Coolants in Car and Light Truck Service
August 1, 2026 - ASTM International

1.1 This practice covers an updated procedure for evaluating corrosion protection and performance of an engine coolant in passenger car, light truck service that closely imitates current vehicle and engine manufacturers' practices. Note 1: Coolant evaluation in vehicle service may...

DNVGL IND SERVICE IV-6-7 - IV-Rules and Guidelines Industrial Services Part 6-Offshore Installations Chapter 7-Guideline for the Construction of Fixed Offshore Installations in Ice Infested Waters
June 1, 2005 - DNVGL

Intention, scope and applicability (1) In extension to the regulations provided by "GL Rules for Classification and Construction: III - Offshore Technology - Part 2: Offshore Installations", this document gives some additional procedures for estimating Sea Ice Properties and Ice Loads on Offshore...

ASTM A1014/A1014M-26 - Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service
July 1, 2026 - ASTM International

1.1 This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of "bolting." 1.2 The following referenced general requirements are indispensable for application of this...

ASTM F2199-26 - Standard Test Method for Determining Dimensional Stability and Curling Properties of Resilient Flooring after Exposure to Heat
August 1, 2026 - ASTM International

4.1 The final appearance of an installed floor depends upon several factors. These include but are not limited to size and squareness in the case of tiles/planks, the quality of joint cut, the quality and preparation of the subfloor and the skill of the installer. Long term appearance of the...

ASTM F1488-26a - Standard Specification for Coextruded Composite Pipe
August 1, 2026 - ASTM International

1.1 This specification covers coextruded composite pipe, intended for non-pressure gravity flow drain waste or vent (DWV) service, or plastic underdrain service, or electrical or comunications conduit service produced by a coextrusion die system, in which the concentric layers...

Advertisement