4.1 Controlled relative humidity environments are important for conditioning materials for shelf-life studies or for investigating the change in physical or dielectric properties after exposure. 4.2 The use of aqueous-glycerin solutions reduces the possibility of contamination of the...
3.1 These test methods are used to evaluate the properties of self-adhesive modified bituminous membranes. The results determine compliance with the applicable specifications, or they can be used for comparative analysis. 3.2 The test methods apply to "as manufactured" material and may not apply to...
5.1 This test method is based on Test Method F903 for measuring resistance of chemical protective clothing materials to penetration by liquids. This test method is normally used to evaluate specimens from individual finished items of protective clothing and individual samples of materials that are...
This specification covers requirements for solvent cements for chlorinated poly(vinyl chloride) (CPVC) plastic pipe, tubing, and socket-type fittings. Solvent cement shall be a CPVC resin-based solution, shall be free-flowing, shall show no gelation or stratification, and shall not contain lumps or...
4.1 The ASTM guidance manual, Form and Style for ASTM Standards, Section A21, requires a precision and bias statement in all ASTM test methods. Section A21.2.2 states: Precision shall be estimated in accordance with the interlaboratory test program prescribed in Practice E691, Conducting an...
1.1 This guide defines the system-level behaviors for computer-based control of major, hazardous, and catastrophic failure conditions. The approaches identified provide behaviors intended to implement the necessary and sufficient controls for each specific failure condition being controlled. These...
4.1 Cartridge adhesives are typically used at job sites in a wide variety of temperature ranges. These products may be exposed to cold temperatures, where one of the limiting application factors is whether the product can be extruded from the cartridge. 4.2 The test method quantitatively measures...
4.1 The final appearance of an installed floor depends upon several factors. These include but are not limited to the manufacture of the flooring material, the preparation of the subfloor and the skill of the installer. This practice is used to measure the ability of the adhesive to retain its...
4.1 This test method determines the procedure to be used to ensure the long term storage stability of aircraft cleaning and maintenance products, in order to ensure their ability to meet the shelf-life requirements called up in specifications or contract documents. The subsequent testing...
4.1 This practice determines the procedure to be used to ensure the long-term storage stability of aircraft cleaning and maintenance products in order to ensure their ability to meet the shelf-life requirements called up in specifications or contract documents. The subsequent testing...
5.1 The purpose of this test method is to obtain reliable values for the WVTR of plastic film and sheeting. 5.2 WVTR is an important property of packaging materials and can often be directly related to shelf life and packaged product stability. 5.3 Data from this test method is suitable as a...
4.1 Penetration resistance is an important end-use performance of thin flexible materials where a sharp-edged product can destroy the integrity of a barrier wrap. This will permit package entry/exit of gases, odors, and unwanted contaminates, causing potential harm to the product and reducing...
This specification covers cold, liquid-applied, single or multi-component, chemically curing, elastomeric secondary edge sealants for sealed structurally glazed insulating glass units. Only the minimum acceptable test requirements for and the durability of these materials are described by this...
5.1 This test method is based on Test Method F903 for measuring resistance of chemical protective clothing materials to penetration by liquids. This test method is normally used to evaluate specimens from individual finished items of protective clothing and individual samples of materials that are...
5.1 Leaks in medical, pharmaceutical, or food product packages can affect product quality and consumer safety. Such leaks can arise from imperfections in package material or between mated components designed to seal the package. Defects can allow unwanted gas (for example, oxygen or water vapor),...
1.1 This test method covers a recommended procedure for examining odor and taste properties of polymeric film intended for use as flexible packaging materials. This test method can be used for single (mono) layers, coextruded, and laminate materials. The focus of this test method is the evaluation...
1.1 This practice covers procedures for measurement of time-related (temporal) sensory perceptions of multiple attributes and events or exposures of products or other sensory stimuli. 1.2 The selection of an appropriate method will depend on the determination of the temporal parameters being...
3.1 The purpose of this practice is to provide the minimum manufacturing requirements for amusement rides and devices and to provide the minimum requirements for a written quality assurance program for an amusement ride or device manufacturer, or component supplier. 3.2 This practice is not...
Narrow Your Results