This test method covers hydraulic cement fineness tests performed using a sieve. The sieve frame should be made of a circular metal matching the specified dimensions, fitted with either a stainless steel woven-wire sieve cloth or an electroformed forced nickel sieve...
1.1 This test method describes the procedures for performing a sieve analysis to determine the particle size distribution of granular infill materials used in artificial turf surface systems. Examples of materials suitable for testing under this method include, but may not be limited to,...
This specification covers standard sand for use in the testing of hydraulic cements. Sand shall meet the requirements with respect to grading, source of sand, and absence of undesirable air entraining characteristics. Sieve analysis shall be performed by sieving the sand by hand or...
This specification covers engineered wood fiber for use as a playground safety surface under and around playground equipment. This specification establishes minimum requirements for the factors that determine particle size, consistency, purity, ability to drain, and heavy metal concentrations...
1.1 These test methods cover procedures for sampling and testing coal ash and raw or calcined pozzolans for use in concrete. 1.2 The procedures appear in the following order: Sections Sampling 7 CHEMICAL ANALYSIS Reagents and apparatus 10 Moisture content 11 and 12 Loss on ignition 13 and 14...
5.1 This test method is intended to provide the user with a procedure to determine slump of plastic concretes. Note 2: This test method was originally developed to provide a technique to monitor the consistency of unhardened concrete. Under laboratory conditions, with strict control of all concrete...
1.1 This test method covers the energy dispersive X-ray fluorescence (EDXRF) spectrochemical analysis of trace levels of uranium and thorium in soils. Any sample matrix that differs from the general ground soil composition used for calibration (that is, fertilizer or a sample of mostly rock) would...
1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 μm (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables. 1.2 This test method...
3.1 This test method determines the size distribution of coke for conformance to specifications of percentages retained on designated screen sizes.
5.1 Thermal power curves are used to evaluate the isothermal hydration kinetics of the combined mixture of different materials during the early period after being mixed with water. These isothermal power curves, or hydration profiles, may provide indications relative to setting characteristics,...
4.1 A dry mass of plastic material is placed on a series of sieves arranged in order of increasing fineness and the mass is divided into fractions corresponding to the sieve opening. 4.2 These test methods are used to determine particle size distribution and therefore are useful for...
1.1 These test methods may be used to determine the water content of soils and the dry density of soils in place using Time Domain Reflectometry. 1.2 These test methods apply to soils that have 30?% or less by weight of their particles retained on the 19.0-mm [3/4-in.] sieve. 1.3 These test...
1.1 These test methods cover the quantitative determination of asphalt binder content in asphalt mixtures and pavement samples. Aggregate obtained by these methods may be used for sieve analysis using Test Method D5444. This test is not appropriate for testing asphalt mixtures containing...
1.1 These test methods cover the analyses usually required on commercial soda ash (sodium carbonate). 1.2 The analytical procedures appear in the following sections: Sections Total Alkalinity, Titrimetric ?8 - 15 Sodium Bicarbonate, Titrimetric 17 - 24 Loss on Heating, Gravimetric 26 - 32 Moisture,...
1.1 This test method covers the determination of the particle size distribution of fine and coarse aggregates by sieving. 1.2 Some specifications for aggregates which reference this test method contain grading requirements including both coarse and fine fractions. Instructions are included...
5.1 During preconstruction and construction evaluations, use of these test methods establishes specific and overall performance characteristics for the mortar system. 5.2 Preconstruction testing of mortars prebatched by weight provides information for the selection of the individual mortar system...
1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...
1.1 This test method covers the evaluation of the particle size distribution of the coarse fraction of sulfur. It is limited to the measurement of those particles greater than 45 μm (No. 325 sieve). 1.2 Units-The values stated in SI units are to be regarded as the standard. No other units of...
4.1 This test method is intended to provide the user with a procedure to determine slump of plastic concretes. Note 2: This test method was originally developed to provide a technique to monitor the consistency of unhardened concrete. Under laboratory conditions, with strict control of all concrete...
Narrow Your Results