loading
ASTM B413-26 - Standard Specification for Refined Silver
July 1, 2026 - ASTM International

1.1 This specification covers refined silver cast bar form in three grades as follows: 1.1.1 Grade 99.90 (UNS P07020)-Silver having a minimum fineness of 999.0 commonly referred to as "commercial bar" or "bullion." 1.1.2 Grade 99.95 (UNS P07015)-Silver having a minimum fineness...

ASTM D3866-18(2026) - Standard Test Methods for Silver in Water
May 1, 2026 - ASTM International

4.1 The principal adverse effect of silver in the body is cosmetic. It causes argyria, a permanent, blue-gray discoloration of the skin, eyes, and mucous membranes. 4.2 Relatively small quantities of silver are bactericidal or bacteriostatic and find limited use in both disinfection...

ASTM B700-26 - Standard Specification for Electrodeposited Coatings of Silver for Engineering Use
May 1, 2026 - ASTM International

1.1 This specification covers requirements for electrodeposited coatings of silver used for engineering purposes that may be matt, bright, or semibright and are not less than 98?mass?% silver purity. 1.2 Coatings of silver covered by this specification are usually employed for...

ASTM C752-18(2026) - Standard Specification for Nuclear-Grade Silver-Indium-Cadmium Alloy
June 1, 2026 - ASTM International

1.1 This specification covers silver-indium-cadmium alloy for use as a control material in light-water nuclear reactors. 1.2 The scope of this specification excludes the use of this material in applications where material strength of this alloy is a prime requisite. Also, this material must...

ASTM B663/B663M-26 - Standard Specification for Silver-Tungsten Carbide Electrical Contact Material
February 1, 2026 - ASTM International

This specification covers electrical contact components made from silver-tungsten carbide by powder metallurgical procedures. This specification covers compositions within the silver-tungsten carbide system. The material shall conform to composition limits. Chemical analysis shall be...

ASTM B662/B662M-26 - Standard Specification for Silver-Molybdenum Electrical Contact Material
February 1, 2026 - ASTM International

1.1 This specification covers electrical contact components made from silver-molybdenum by powder metallurgical procedures. 1.2 This specification covers compositions within the silver-molybdenum system for electrical contact applications. 1.3 The values stated in either SI units or...

ASTM D8607-26 - Standard Test Method for Determination of Selected Elements in Aqueous Solutions by Single Quadrupole Inductively Coupled Plasma-Mass Spectrometry (ICP-MS)
July 1, 2026 - ASTM International

1.1 This test method covers the determination of dissolved elements in ground waters, surface waters, and drinking water. It may also be used for determination of total recoverable or total element concentrations in these waters as well as wastewater, mine-impacted waters, and digested biosolids,...

ASTM E3325-21(2026) - Standard Practice for Sampling of Solar Photovoltaic Modules for Toxicity Testing
June 1, 2026 - ASTM International

1.1 The purpose of this practice is to describe a representative and repeatable sample preparation methodology to conduct toxicity testing on solar photovoltaic (PV) modules for use with EPA Test Method 1311: Toxicity Characteristic Leaching Procedure (TCLP). 1.2 This practice refers to the...

ASTM D8084-26 - Standard Test Method for Photoelectrochemical Oxygen Demand of Freshwater Sources for Drinking Water Treatment Plants and Treated Drinking Water
January 1, 2026 - ASTM International

5.1 This test method describes a rapid method to determine the maximum quantity of oxygen that may be consumed by impurities in water. As outlined in Test Methods D1252, chemical oxygen demand is typically used to monitor and control oxygen-consuming pollutants, both organic and inorganic, in...

ASTM D3634-21(2025) - Standard Test Method for Trace Chloride Ion in Engine Coolants
October 15, 2025 - ASTM International

1.1 This test method covers the determination of chloride ion in engine coolants in the range from 5?ppm to 200 ppm in the presence of up to 0.6 weight?% mercaptobenzothiazole. 1.2 Other materials that react with silver ion will interfere. 1.3 Chloride in engine coolants containing an...

ASTM E1587-25a - Standard Test Methods for Chemical Analysis of Refined Nickel
November 15, 2025 - ASTM International

1.1 These test methods apply to the chemical analysis of refined nickel and other forms of metallic nickel having chemical compositions within the following limits: Element Mass Fraction, % Antimony, less than 0.005 Arsenic, less than 0.005 Bismuth, less than 0.01 Cadmium, less than 0.0025 Carbon,...

ASTM B678-25 - Standard Test Method for Solderability of Metallic-Coated Products
November 1, 2025 - ASTM International

1.1 This test method provides a procedure for evaluating the solderability of metallic-coated products and test specimens to assure satisfactory performance in manufacturing processes requiring soldering with soft (tin-lead) solder and rosin flux. This test method is applicable only for testing...

ASTM E2823-25 - Standard Test Method for Analysis of Nickel Alloys by Inductively Coupled Plasma Mass Spectrometry (Performance-Based)
November 1, 2025 - ASTM International

1.1 This test method describes the inductively coupled plasma mass spectrometric analysis of nickel and nickel alloys, as specified by Committee B02, and having chemical compositions within the following limits: Element Application Range (Mass Fraction %) Aluminum 0. 01-6.00 Boron 0. 01-0.10 Carbon...

ASTM E354-25 - Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys
November 15, 2025 - ASTM International

1.1 These test methods cover the chemical analysis of high-temperature, electrical, magnetic, and other similar iron, nickel, and cobalt alloys having chemical compositions within the following limits: ??Element Composition Range,?% Aluminum 0.005 to 18.00 Beryllium 0.001 to ?0.05 Boron 0.001 to ?1...

ASTM B890-25 - Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
September 1, 2025 - ASTM International

5.1 This test method allows the determination of the chemical composition of powdered and sintered tungsten-based hardmetals. This test method is not applicable to material which will not oxidize readily at high temperatures in air, such as tungsten/copper, tungsten/silver alloys, or...

ASTM E246-25 - Standard Test Methods for Determination of Iron in Iron Ores and Related Materials by Dichromate Titrimetry
October 1, 2025 - ASTM International

1.1 These test methods cover the determination of total iron in iron ores, concentrates, and agglomerates from 30?% to 95?% iron. 1.2 The test methods in this standard are contained in the sections indicated as follows: Test Method?A- Iron by the Hydrogen Sulfide Reduction Dichromate Titration...

ASTM A482/A482M-11(2025) - Standard Specification for Ferrochrome-Silicon
September 1, 2025 - ASTM International

This specification covers ferrochrome-silicon of Grades A and B. Chemical analysis shall be performed wherein specimens shall conform to required chemical composition of chromium, carbon, silicon, sulfur, phosphorus, nitrogen, manganese, nickel, vanadium, copper, molybdenum, columbium, tantalum,...

ASTM D2988-96(2025) - Standard Test Methods for Water-Soluble Halide Ion in Halogenated Organic Solvents and Their Admixtures
August 1, 2025 - ASTM International

1.1 Test Methods 1, 2, and 3-These test methods cover the determination of water-extractable halide ion in halogenated organic solvents and their admixtures. Fluoride ion is not measured due to the solubility of silver fluoride. 1.2 Test Method 4-This test method covers the determination of...

ASTM D8186-25 - Standard Test Method for Measurement of Impurities in Graphite by Electrothermal Vaporization Inductively Coupled Plasma Optical Emission Spectrometry (ETV-ICP-OES)
August 15, 2025 - ASTM International

1.1 This test method covers the measurement of mass fractions of the elements silver (Ag), aluminum (Al), arsenic (As), boron (B), barium (Ba), berylium (Be), bismuth (Bi), calcium (Ca), cadmium (Cd), cobalt (Co), chromium (Cr), copper (Cu), iron (Fe), potassium (K), lithium (Li), magnesium...

ASTM B877-25 - Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method
July 1, 2025 - ASTM International

1.1 This test standard covers equipment and methods for using phosphomolybdic acid (PMA) to detect gross defects and mechanical damage including wear through in metallic coatings of gold, silver, or palladium. These metals comprise the topmost metallic layers over substrates of nickel,...

Advertisement