1.1 Practice D7897 applies to simulation of the effects of field exposure on the solar reflectance and thermal emittance of roof surface materials including but not limited to field-applied coatings, factory-applied coatings, single-ply membranes, modified bitumen products, shingles, tiles,...
4.1 Upon deployment, at the site of the vascular stenosis, the stent establishes the patency of the lumen until vascular remodeling occurs. The radial load acting upon the stent is imparted by vessel and lesion stretch. Additionally, the vessel might be affected by excursions due to pulsation...
1.1 These practices cover the calculation of profilograph response to longitudinal profiles of traveled surface roughness. 1.2 These practices utilize computer simulations to obtain profilograph responses, including surface sensing wheel (recording wheel) vertical displacement and reference...
4.1 Reliable dosimetry is indispensable for research on the effects of ionizing radiation on materials and products. Without reliable dosimetry valid conclusions cannot be reached, or the wrong conclusions might be reached. 4.2 This document is intended to provide direction on how to conduct...
5.1 Corrosion inhibitors continue to play a key role in controlling internal corrosion associated with oil and gas production and transportation. This results primarily from the industry's extensive use of carbon and low alloy steels, which, for many applications, are economic materials of...
5.1 There is interest from industry and CAAs to create a means of compliance for software assurance for UAS, particularly in instances where conventional design assurance requirement management processes may over-prescribe requirements in relation to the level of risk of the UAS operation, or of...
4.1 Capturing high quality RAM performance data requires careful and consistent collection of equipment failure and repair data, operating hours, and repair time. A standard hierarchy of equipment boundaries has been needed for machinery data exchange among the stakeholders in shipbuilding, ship...
4.1 Use as an Analytical Tool-Mathematical methods provide an analytical tool to be employed for many applications related to absorbed dose determinations in radiation processing. Mathematical calculations may not be used as a substitute for routine dosimetry in some applications (for example,...
4.1 Significance: 4.1.1 When conducting exposures in devices that use laboratory light sources, it is important to consider how well the accelerated test conditions will reproduce property changes and failure modes associated with end-use environments for the materials being tested. In addition, it...
1.1 This test method covers the procedure to determine the amount of deposits formed by automotive engine oils utilizing the thermo-oxidation engine oil simulation test (TEOST2).3 An interlaboratory study (see Section 17) has determined it to be applicable over the range from 10?mg to 65?mg...
4.1 The safety margins provided in the design for a component or structure can be reduced throughout its service life by aging. Aging is the process by which the physical and mechanical characteristics of component or structure materials change with time or use; this process may proceed by a single...
This practice provides application criteria, definitions, and supplemental information to assist the user in obtaining meaningful vacuum ionization gage measurements in space-simulation facilities. Acceptable vacuum-measuring equipment shall consist of those items in which performance is...
1.1 These test methods cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided,...
1.1 This guide applies to unmanned aircraft (UA) with a maximum dimension (for example, wingspan, disk diameter) =?25?ft (=?7.68 m) operating at airspeeds below 100?kts and of any configuration or category. It is meant to be applied in a "lower risk" (low- and medium-risk airspace as described by...
5.1 Evaluation Strategy: 5.1.1 Corrosion fatigue evaluation of absorbable metals may be useful for screening and validation of alloys, processes, and coatings, and also for verification and validation of fully designed implants. Corrosion fatigue testing may also be useful for informing an in vitro...
4.1 This guide is intended to encourage consistency and thoroughness in the application of geostatistical simulation to environmental, geotechnical, and hydrogeological site investigations. 4.2 This guide may be used to assist those performing a simulation study or as an explanation...
4.1 These test methods are intended to evaluate the duration for which the types of building elements noted in 1.1 contain a fire, retain their structural integrity, or exhibit both properties during a predetermined test exposure. 4.2 The test exposes a test specimen to a standard fire controlled...
1.1 This standard specifies the dimensions of knife-edge style flanges and their associated gaskets used in vacuum systems for pressures ranging from 105 Pa to 10-11 Pa. Such flanges are widely used throughout vacuum technology applications in semiconductor processing tools, surface analysis...
5.1 The test method is designed to predict the deposit-forming tendencies of engine oil in the piston ring belt and upper piston crown area. Correlation has been shown between the TEOST MHT procedure and the TU3MH Peugeot engine test in deposit formation. Such deposits formed in the ring-belt area...
Narrow Your Results