loading
HI TABLE OF CONTENTS - Centrifugal Pumps for Nomenclature and Definitions
January 1, 2000 - HI/HYDRAUL
A description is not available for this item.
ASTM F2388-21(2026) - Standard Consumer Safety Specification for Baby Changing Products for Domestic Use
July 1, 2026 - ASTM International

1.1 This consumer safety specification covers performance requirements, test methods, and labeling requirements to promote the safe use of baby changing products including changing tables, changing table accessories, contoured changing pads, and add-on changing units. 1.2 This...

ASTM E390-20(2026) - Standard Reference Radiographs for Steel Fusion Welds
July 1, 2026 - ASTM International

4.1 These reference radiographs may be used as a means for establishing the types and severity levels of discontinuities that are revealed by radiographic examination of steel fusion welds. 4.2 Personnel utilizing reference radiographs to this standard shall be qualified and authorized to perform...

ASTM D1319-26 - Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
July 1, 2026 - ASTM International

1.1 This test method covers the determination of hydrocarbon types of total aromatics, total olefins, and total saturates in petroleum fractions that distill below 315?°C. Samples containing dark-colored components that interfere in reading the chromatographic bands cannot be analyzed. Note 1: For...

ASTM D6752/D6752M-26 - Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method
August 1, 2026 - ASTM International

1.1 This test method covers the determination of bulk specific gravity of compacted asphalt mixtures by the vacuum sealing method. 1.2 This method can be used for compacted cylindrical and cubical laboratory and field asphalt mixture specimens. 1.3 The bulk specific gravity of the compacted asphalt...

ASTM F1488-26a - Standard Specification for Coextruded Composite Pipe
August 1, 2026 - ASTM International

1.1 This specification covers coextruded composite pipe, intended for non-pressure gravity flow drain waste or vent (DWV) service, or plastic underdrain service, or electrical or comunications conduit service produced by a coextrusion die system, in which the concentric layers are formed and...

ASTM D4354-26 - Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products (RECPs) for Testing
July 1, 2026 - ASTM International

1.1 This practice covers three procedures for the sampling of geosynthetics and rolled erosion control products (RECPs) for testing. This practice requires that instructions on taking laboratory samples and test specimens be part of every test method for geosynthetics. 1.1.1 The first procedure...

ASTM E1320-20(2026) - Standard Reference Radiographs for Titanium Castings
July 1, 2026 - ASTM International

1.1 The reference radiographs provided in the adjunct to this standard are reproductions of original radiographs and are supplied as a means for establishing some of the categories and severity levels of discontinuities in titanium castings that may be revealed by radiographic examination. Use of...

ASTM B737-10(2026) - Standard Specification for Hot-Rolled and/or Cold-Finished Hafnium Rod and Wire
July 1, 2026 - ASTM International

15.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding methods of Practice E29. Property Rounded Unit for...

ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

1.1 This specification covers requirements, test methods, and marking requirements for system components when tested with nominal SDR9 crosslinked polyethylene (PEX) tubing as a system. Systems are intended for 100 psi (0.69 MPa) water service up to and including a maximum working temperature of...

ASTM C129-26 - Standard Specification for Dry-Cast Nonloadbearing Concrete Masonry Units
July 15, 2026 - ASTM International

1.1 This specification covers dry-cast hollow and solid nonloadbearing concrete masonry units machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These units are intended for use in nonloadbearing partitions, but under certain...

ASTM C1540-26 - Standard Specification for Heavy-Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
July 15, 2026 - ASTM International

1.1 This specification covers the evaluation of the performance of heavy-duty shielded couplings to join hubless cast iron soil pipe and fittings. 1.2 Couplings covered by this standard shall have nominal dimensions as found in Table 1 and Fig. 1. 1.3 The values stated in inch-pound units...

ASTM B163-26 - Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
July 1, 2026 - ASTM International

1.1 This specification covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service. 1.2 This specification covers outside diameter and average wall, or outside diameter and minimum wall tube. 1.2.1 The sizes covered by this...

ASTM D1655-26b - Standard Specification for Aviation Turbine Fuels
June 15, 2026 - ASTM International

1.1 This specification covers the use of purchasing agencies in formulating specifications for purchases of aviation turbine fuel under contract. 1.2 This specification defines the minimum property requirements for Jet A and Jet A-1 aviation turbine fuel and lists acceptable additives for use in...

ASTM D1238-26 - Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
July 15, 2026 - ASTM International

5.1 This test method is particularly useful for quality control tests on thermoplastics. 5.2 The data produced by this test method serves to indicate the uniformity of the flow rate of the polymer as made by an individual process. It is not to be used as an indication of uniformity of other...

ASTM D7192-26 - Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
July 1, 2026 - ASTM International

4.1 This test method is designed to provide load versus deformation response of plastic films under essentially multi-axial deformation conditions at impact velocities. This test method further provides a measure of the rate sensitivity of the plastic films to impact. 4.2 Multi-axial impact...

ASTM D7611/D7611M-26 - Standard Practice for Coding Plastic Manufactured Articles for Resin Identification
July 1, 2026 - ASTM International

4.1 Resin Identification Codes are used solely to identify the plastic resin used in a manufactured article. The intended manufactured articles include, but are not limited to, packaging. 4.1.1 Fig. 1 and Table 1 present the appropriate information on the way the RIC is to be incorporated...

ASTM D5790-18(2026) - Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry
July 1, 2026 - ASTM International

1.1 This test method covers the identification and simultaneous measurement of purgeable volatile organic compounds. It has been validated for treated drinking water, wastewater, and ground water. This test method is not limited to these particular aqueous matrices; however, the applicability of...

ASTM F3125/F3125M-26 - Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi, 144 ksi, and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength
July 1, 2026 - ASTM International

1.1 This specification covers chemical, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch and metric dimensions, in two strength grades, two types and two styles. 1.1.1 This specification was originally issued as a consolidation...

Advertisement