loading
ARP5483B - Rolling Element Bearing Test Methods
April 26, 2023 - SAE International

This SAE Aerospace Recommended Practice (ARP) establishes methods for testing airframe rolling element bearings. The purpose of ARP5483 and its associated slash sheets is to document test methods commonly used to evaluate airframe bearings. These test methods may be referenced in standards,...

ARP5448B - Plain Bearing Test Methods
August 23, 2018 - SAE International

This SAE Aerospace Recommended Practice (ARP) establishes methods for testing airframe plain bearings. The purpose of ARP5448 and its associated slash sheets is to document test methods commonly used to evaluate airframe bearings. These test methods may be referenced in specifications, part...

ASTM F2033-25 - Standard Specification for Hip Joint Replacement Bearing Surfaces
July 1, 2025 - ASTM International

This specification covers the design and dimensional requirements for metallic, ceramic, and polymeric mating bearing surfaces used in total hip joint prostheses and hip endoprostheses, more specifically, hip joint replacements of the ball-and-socket configuration. This specification covers...

AIR1594D - Plain Bearing Selection for Landing Gear Applications
August 23, 2023 - SAE International

This document is intended to give advisory information for the selection of plain bearings and bearing materials most suitable for aircraft landing gear applications. Information included herein was derived from bearing tests and service experience/reports. Airframe/landing gear...

ASTM E238-17a(2025) - Standard Test Method for Pin-Type Bearing Test of Metallic Materials
November 1, 2025 - ASTM International

1.1 This test method covers a pin-type bearing test of metallic materials to determine bearing yield strength and bearing strength. Note 1: The presence of incidental lubricants on the bearing surfaces may significantly lower the value of bearing yield strength...

GME B 040 1037 - Bearing shell lubricating oil
November 1, 2016 - GME

Application: For the circulation lubrication of the bearing shell to Hatebur presses.

GMW18273 - Powertrain Take-Off Unit (PTU) Synthetic Lubricant
June 1, 2020 - GMW

Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose/Material Description. This is the specification for GM Part Number 9986482 which is a...

ASTM D6511/D6511M-18(2024) - Standard Test Methods for Solvent Bearing Bituminous Compounds
May 1, 2024 - ASTM International

1.1 These test methods cover procedures for sampling and testing solvent bearing bituminous compounds for use in roofing and waterproofing. 1.2 The test methods appear in the following order: Section Sampling 4 Uniformity 5 Weight per gallon 6 Nonvolatile content 7 Solubility 8 Ash content 9...

JIS G 4805 - High carbon chromium bearing steels
March 20, 2019 - JSA

This Standard specifies the requirement for high carbon chromium bearing steels (hereafter referred to as steels) used for roller bearings. NOTE The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 683-17 : 2014 Heat-treated...

ASABE S331 - Implement Power Take-Off Drive Shaft Specifications
December 1, 2020 - ASABE

Purpose The purpose of this Standard is to establish multiple categories of power take-off (PTO) drive shafts, each with a regular duty subset and a heavy duty subset. A PTO drive shaft is intended for use to transmit rotational mechanical power from a tractor PTO to an implement power input...

GM196M - Composite Bearing Material
August 1, 2011 - GMNA

1 SCOPE. This specification covers high performance composite bearing materials consisting of a steel backing plate, having a sintered bronze layer which is impregnated with a polytetrafluoroethylene (PTFE) - lead/lead oxide mixture. These composite bearing materials have a useful...

Estimation of take-off distance
June 1, 2010 - ESDU

INTRODUCTION The method presented in this Data Item is suitable only in the early stages of a design project. It is also assumed that the tyre-runway friction interaction is dealt with in an approximate way using gross assumptions: other Items in the Performance Series provide more comprehensive...

GMW14589 - Objective Measurement of Dynamic Wheel Bearing Drag
October 1, 2016 - GMW

Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. The purpose of the test is to quantify the dynamic drag torque of wheel...

ARP5483/2A - Rolling Element Bearing Hardness Test
July 24, 2017 - SAE International

This method outlines the standard procedure for testing the hardness of bearing components. Bearings covered by this test method shall be any rolling element bearing used in airframe control.

GMKOREA EDS-M-1401 - Aluminum Metal Bearing
April 1, 2011 - GMKOREA

Material Description. This standard specifies aluminum metal bearing used by GM Korea Company (hereinafter referred to as the "GM Korea").

J459_201801 - Bearing and Bushing Alloys
January 10, 2018 - SAE International

The bearing performance of steel backed half bearings, bushings, and washers is dependent on the properties and thickness of the lining alloy, the strength and dimensional stability of the steel backing (usually SAE 1010) and the strength of the bond between the lining alloy and the backing....

GMKOREA EDS-T-2110 - Clutch Release Bearing
December 1, 2011 - GMKOREA

This specification is applied to clutch system for manual transmission of passenger car. PURPOSE This specification evaluate service life of clutch release bearing of assembly flywheel, clutch cover and clutch plate, clutch housing.

ASTM C607-88(2024) - Standard Practice for Coking Large Shapes of Carbon-Bearing Materials
August 1, 2024 - ASTM International

1.1 This practice covers the preparation of coking of carbon-bearing material for subsequent testing such as modulus of rupture, slag testing, thermal conductivity, and thermal expansion. Test Methods C831 is the specified method for testing residual carbon. 1.2 The values stated in...

ASTM D1404/D1404M-99(2025) - Standard Test Method for Estimation of Deleterious Particles in Lubricating Grease
November 1, 2025 - ASTM International

5.1 The significance of the number of scratches as far as correlation with field performance is concerned has not been established. A particle which is abrasive to plastic will not necessarily be abrasive to steel or other bearing materials. Some correlation was obtained in that the...

ARP5448/7A - Plain Bearing Wear Measurement
December 12, 2016 - SAE International

This standard details two methods of inspecting PTFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the...

Advertisement