loading
AWWA TANK SET - AWWA TANK SET
AWWA
A description is not available for this item.
ASTM E2256-26 - Standard Guide for Hydraulic Integrity of New, Repaired, or Reconstructed Aboveground Storage Tank Bottoms for Petroleum Service
May 1, 2026 - ASTM International

1.1 This guide is intended to provide the reader with a knowledge of construction examination procedures and current technologies that can be used to give an owner or operator of an aboveground storage tank (AST) in petroleum service, relevant information on the hydraulic integrity of a new,...

ASTM D2624-26 - Standard Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
July 1, 2026 - ASTM International

1.1 These test methods cover the determination of the electrical conductivity of aviation and distillate fuels with and without a static dissipator additive. The test methods normally give a measurement of the conductivity when the fuel is uncharged, that is, electrically at rest (known as the rest...

ASTM E3494-26 - Standard Test Method for Effectiveness of Antifoaming Agents for Agriculture Tank Mix
May 1, 2026 - ASTM International

5.1 This test method is designed to determine the ability of an antifoam to reduce or eliminate the formation of undesirable foam that can be generated during the mixing and application of agricultural chemicals in dilute aqueous mixtures. 5.2 This test method may be used to determine the relative...

ASTM D3299-26 - Standard Specification for Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
April 1, 2026 - ASTM International

This specification covers cylindrical corrosion-resistant tanks made of commercial-grade glass-fiber-reinforced polyester or vinylester thermoset resin fabricated by filament winding for above-ground vertical installation, to contain aggressive chemicals at atmospheric pressure as classified...

ASTM F3826-26 - Standard Specification for Liquid Energy Storage Systems for Light Sport Category Aircraft
May 1, 2026 - ASTM International

1.1 This specification covers requirements for liquid energy storage systems-fuel tanks-for light sport category aircraft. 1.2 This specification only addresses liquid energy storage systems that are either vented to the atmosphere or are pressurized to less than one atmosphere. 1.3...

ASTM D8615-26 - Standard Test Method for Freezing Point of Aviation Fuels (Automatic Coaxial Optical Fibers Method)
March 1, 2026 - ASTM International

5.1 The freezing point of an aviation fuel is the lowest temperature at which the fuel remains free of solid hydrocarbon crystals that can restrict the flow of fuel through filters if present in the fuel system of the aircraft. The temperature of the fuel in the aircraft tank normally...

ASTM D8265-26 - Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes
April 1, 2026 - ASTM International

1.1 These practices describe standard procedures for using electrical methods to locate leaks in geomembranes covered with liquid or earthen materials, or both. 1.2 These practices are intended to ensure that leak location surveys are performed to the highest technical capability of electrical...

ASTM D8630-26 - Standard Test Method for Freezing Point of Aviation Fuels (Micro CFP Method)
March 1, 2026 - ASTM International

5.1 The freezing point of an aviation fuel is the lowest temperature at which the fuel remains free of solid hydrocarbon crystals. Hydrocarbon crystals can restrict the flow of fuel through the fuel system of the aircraft. The temperature of the fuel in the aircraft tank normally decreases...

ASTM C1696-26 - Standard Guide for Industrial Thermal Insulation Systems
March 1, 2026 - ASTM International

4.1 When choosing a thermal insulation product or combination of products, physical, chemical and mechanical properties and the significance of those properties should be considered. ASTM test methods are usually performed under laboratory conditions and may not accurately represent field...

ASTM D8152-26 - Standard Practice for Measuring Field Infiltration Rate and Calculating Field Hydraulic Conductivity Using the Modified Philip Dunne Infiltrometer Test
February 15, 2026 - ASTM International

5.1 This practice shall only be used on soils having infiltration rates ranging from 2.5 mm/h (field hydraulic conductivity of 6.9?×?10-7 m/s) to 15000 mm/h (field hydraulic conductivity of 4.0?×?10-3 m/s). 5.2 This practice is useful for field measurement of the infiltration rate and calculation...

ASTM D2759-00(2026) - Standard Practice for Sampling Gas from a Transformer Under Positive Pressure
January 1, 2026 - ASTM International

2.1 A gas sample from above the insulating liquid in transformers and other electrical power apparatus can be used to give an early indication of developing fault conditions. Combustible gases are formed from the breakdown of the insulating materials under thermal and electrical stress. Excessive...

ASTM D7153-25a - Standard Test Method for Freezing Point of Aviation Fuels (Automatic Laser Method)
December 15, 2025 - ASTM International

5.1 The freezing point of an aviation fuel is the lowest temperature at which the fuel remains free of solid hydrocarbon crystals which, if present in the fuel system of the aircraft, can restrict the flow of fuel through filters. The temperature of the fuel in the aircraft tank normally...

ASTM B320-25 - Standard Practice for Preparation of Iron Castings for Electroplating
November 1, 2025 - ASTM International

This practice covers preparation of iron castings for electroplating and is intended to assist electroplaters in establishing and maintaining a satisfactory pre-electroplating cycle for malleable iron, gray iron, nodular iron, and white iron castings. It is also intended to indicate certain foundry...

ASTM D7111-16(2025) - Standard Test Method for Determination of Trace Elements in Middle Distillate Fuels by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
November 1, 2025 - ASTM International

5.1 Trace elemental analysis is used to indicate the level of contamination of middle distillate fuels. Trace metals in turbine fuels can cause corrosion and deposition on turbine components at elevated temperatures. Some diesel fuels have specification limit requirements for trace metals to guard...

ASTM D6442-06(2026) - Standard Test Method for Determination of Copper Release Rate From Antifouling Coatings in Substitute Ocean Water
January 1, 2026 - ASTM International

1.1 This test method covers the laboratory determination of the rate at which copper is released from an antifouling (AF) coating in substitute ocean water. The practical limits for quantifying copper release rates by this method are from 1.8?μg cm-2d-1 to 500 μg cm-2d-1. This range may be extended...

ASTM D870-25 - Standard Practice for Testing Water Resistance of Coatings Using Water Immersion
November 1, 2025 - ASTM International

4.1 Immersion in water can cause the degradation of coatings. Knowledge on how a coating resists water immersion is helpful in predicting its service life. Failure in a water immersion test may be caused by a number of factors including a deficiency in the coating itself, contamination of the...

Advertisement