1.1 This test method covers the resistance to freezing and thawing of dry-cast segmental retaining wall (SRW) units (see Specification C1372) and related concrete units. Units are tested in a test solution that is either potable tap water or 3 % saline solution depending on the intended use...
This specification covers the dimensions and tolerances for both driving and driven elements in square drive interconnections on stainless steel surgical instruments used for drilling, tapping, driving, or placing of medical devices during surgery. The specification is intended to lessen the...
1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection,...
1.1 This test method covers the procedure for a finite flash point test, within the range of -25?°C to 90?°C, of liquid wastes using an MCCCFP tester. This test method is used in the determination of flash point of liquid wastes. Note 1: The connection of tap water or a cooling device may be...
1.1 This test method covers the determination of dissolved and total recoverable barium in most waters and wastewaters. 1.2 This test method was evaluated in the range from 33.5?μg/L to 132?μg/L of barium. The range can be increased or decreased by varying the volume of sample injected or the...
5.1 This test method is fully quantitative and it also avoids any loss of viable organisms through wash off, making it possible to produce statistically valid data using many fewer test and control carriers than other quantitative methods based on most probable numbers (MPN). 5.2 The design of the...
This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe and tubing. Fittings covered by this specification are normally molded. In-line fittings such as couplings, unions, bushings, caps, nipples, etc., may be extruded or machined from...
1.1 This test method describes a laboratory technique to evaluate the mean lubricant efficiency of metal removal fluids using an instrumented tapping machine that measures and records torque. 1.1.1 The method is applicable to all tap types, machining speeds, and alloys that can be...
This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs, including heat-treated machine screws, tapping screws, and sems. Types of surface discontinuities are: crack;...
1.1 This test method2 covers the determination of total mercury in water in the range from 0.5?μg to 10.0?μg Hg/L (1).3 The test method is applicable to fresh waters, saline waters, and some industrial and sewage effluents. It is the user's responsibility to ensure the validity of this test method...
1.1 This test method describes a method for the laboratory measurement of the effectiveness of floor coverings in reducing impact noise from a standard tapping machine through concrete floors. The test results are not necessarily directly related to the subjective evaluations of the floor...
1.1 This test method covers the laboratory measurement of impact sound transmission of floor-ceiling assemblies using a standardized tapping machine. It is assumed that the test specimen constitutes the primary sound transmission path into a receiving room located directly below and that a...
1.1 This specification2 covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4 in. and under in diameter for application at normal atmospheric temperatures, where high strength is required and for limited...
1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection,...
1.1 This test method covers the measurement of the transmission of impact sound generated by a standard tapping machine through floor-ceiling assemblies and associated supporting structures in field situations. 1.2 Results are measurable for all types of floor-ceiling assemblies, including...
1.1 These test methods cover the determination of hexavalent and total chromium in water. Section 34 on Quality Control pertains to these test methods. Three test methods are included as follows: Test Method Concentration Range Sections A-Photometric Diphenyl- carbohydrazide ?0.01?mg/L to 0.5?mg/L...
1.1 This test method covers the determination of dissolved and total recoverable vanadium in most waters and wastewater by graphite furnace atomic absorption spectrophotometry. 1.2 The optimum range of this test method is 10?μg/L to 200?μg/L of vanadium based on a 20?μL sample size. Concentrations...
1.1 This test method covers the determination of dissolved and total recoverable antimony in water by atomic absorption spectroscopy.2 1.2 This test method is applicable in the range from 1?μg/L to 15?μg/L of antimony. The range may be extended by less scale expansion or by dilution of the sample....
5.1 Pesticides and herbicides may be used in various agricultural and household products. These products may enter waterways at low levels through runoff or misuse near water resources. There is a need for a quick, easy, and robust method to determine pesticide concentration in water matrices for...
Narrow Your Results