loading
ASTM C1262/C1262M-26 - Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
June 1, 2026 - ASTM International

1.1 This test method covers the resistance to freezing and thawing of dry-cast segmental retaining wall (SRW) units (see Specification C1372) and related concrete units. Units are tested in a test solution that is either potable tap water or 3 % saline solution depending on the intended use...

ASTM F2062-00(2026) - Standard Specification for Square Drive Interconnections on Surgical Instruments
May 1, 2026 - ASTM International

This specification covers the dimensions and tolerances for both driving and driven elements in square drive interconnections on stainless steel surgical instruments used for drilling, tapping, driving, or placing of medical devices during surgery. The specification is intended to lessen the...

ASTM A74-26 - Standard Specification for Cast Iron Soil Pipe and Fittings
April 1, 2026 - ASTM International

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection,...

ASTM D8606-26 - Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Modified Continuously Closed Cup (MCCCFP) Tester
May 1, 2026 - ASTM International

1.1 This test method covers the procedure for a finite flash point test, within the range of -25?°C to 90?°C, of liquid wastes using an MCCCFP tester. This test method is used in the determination of flash point of liquid wastes. Note 1: The connection of tap water or a cooling device may be...

ASTM D4382-18(2026) - Standard Test Method for Barium in Water, Atomic Absorption Spectrophotometry, Graphite Furnace
May 1, 2026 - ASTM International

1.1 This test method covers the determination of dissolved and total recoverable barium in most waters and wastewaters. 1.2 This test method was evaluated in the range from 33.5?μg/L to 132?μg/L of barium. The range can be increased or decreased by varying the volume of sample injected or the...

ASTM E2111-26 - Standard Test Method to Evaluate the Bactericidal, Fungicidal, Mycobactericidal, and Sporicidal Potencies of Liquid Chemicals using Quantitative Carriers (Quantitative Carrier Test-Tier 1)
March 1, 2026 - ASTM International

5.1 This test method is fully quantitative and it also avoids any loss of viable organisms through wash off, making it possible to produce statistically valid data using many fewer test and control carriers than other quantitative methods based on most probable numbers (MPN). 5.2 The design of the...

ASTM D2683-26 - Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
February 1, 2026 - ASTM International

This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe and tubing. Fittings covered by this specification are normally molded. In-line fittings such as couplings, unions, bushings, caps, nipples, etc., may be extruded or machined from...

ASTM D8288-25 - Standard Test Method for Comparison of Metalworking Fluids Using a Tapping Torque Test Machine
November 1, 2025 - ASTM International

1.1 This test method describes a laboratory technique to evaluate the mean lubricant efficiency of metal removal fluids using an instrumented tapping machine that measures and records torque. 1.1.1 The method is applicable to all tap types, machining speeds, and alloys that can be...

ASTM F788/F788M-20(2025) - Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
October 1, 2025 - ASTM International

This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs, including heat-treated machine screws, tapping screws, and sems. Types of surface discontinuities are: crack;...

ASTM D3223-17(2025) - Standard Test Method for Total Mercury in Water
December 1, 2025 - ASTM International

1.1 This test method2 covers the determination of total mercury in water in the range from 0.5?μg to 10.0?μg Hg/L (1).3 The test method is applicable to fresh waters, saline waters, and some industrial and sewage effluents. It is the user's responsibility to ensure the validity of this test method...

ASTM E2179-25 - Standard Test Method for Laboratory Measurement of the Effectiveness of Floor Coverings in Reducing Impact Sound Transmission Through Concrete Floors
October 15, 2025 - ASTM International

1.1 This test method describes a method for the laboratory measurement of the effectiveness of floor coverings in reducing impact noise from a standard tapping machine through concrete floors. The test results are not necessarily directly related to the subjective evaluations of the floor...

ASTM E492-25 - Standard Test Method for Laboratory Measurement of Impact Sound Transmission Through Floor-Ceiling Assemblies Using the Tapping Machine
August 15, 2025 - ASTM International

1.1 This test method covers the laboratory measurement of impact sound transmission of floor-ceiling assemblies using a standardized tapping machine. It is assumed that the test specimen constitutes the primary sound transmission path into a receiving room located directly below and that a...

ASTM A354-17(2025) - Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners
October 1, 2025 - ASTM International

1.1 This specification2 covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4 in. and under in diameter for application at normal atmospheric temperatures, where high strength is required and for limited...

ASTM A74-25 - Standard Specification for Cast Iron Soil Pipe and Fittings
August 15, 2025 - ASTM International

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection,...

ASTM E1007-25 - Standard Test Method for Field Measurement of Tapping Machine Impact Sound Transmission Through Floor-Ceiling Assemblies and Associated Support Structures
August 1, 2025 - ASTM International

1.1 This test method covers the measurement of the transmission of impact sound generated by a standard tapping machine through floor-ceiling assemblies and associated supporting structures in field situations. 1.2 Results are measurable for all types of floor-ceiling assemblies, including...

ASTM D1687-17(2025) - Standard Test Methods for Chromium in Water
July 1, 2025 - ASTM International

1.1 These test methods cover the determination of hexavalent and total chromium in water. Section 34 on Quality Control pertains to these test methods. Three test methods are included as follows: Test Method Concentration Range Sections A-Photometric Diphenyl- carbohydrazide ?0.01?mg/L to 0.5?mg/L...

ASTM D3373-17(2025) - Standard Test Method for Vanadium in Water
July 1, 2025 - ASTM International

1.1 This test method covers the determination of dissolved and total recoverable vanadium in most waters and wastewater by graphite furnace atomic absorption spectrophotometry. 1.2 The optimum range of this test method is 10?μg/L to 200?μg/L of vanadium based on a 20?μL sample size. Concentrations...

ASTM D3697-17(2025) - Standard Test Method for Antimony in Water
July 1, 2025 - ASTM International

1.1 This test method covers the determination of dissolved and total recoverable antimony in water by atomic absorption spectroscopy.2 1.2 This test method is applicable in the range from 1?μg/L to 15?μg/L of antimony. The range may be extended by less scale expansion or by dilution of the sample....

ASTM D8574-25 - Standard Test Method for Determination of Select Pesticides and Herbicides in Water by Liquid Chromatography Tandem Mass Spectrometry (LC-MS/MS)
May 1, 2025 - ASTM International

5.1 Pesticides and herbicides may be used in various agricultural and household products. These products may enter waterways at low levels through runoff or misuse near water resources. There is a need for a quick, easy, and robust method to determine pesticide concentration in water matrices for...

DNV TAP NO. 4-732.10-1 - Gas Turbines
October 1, 2011 - DNVGL
A description is not available for this item.
Advertisement