loading
HI WATER TREATMENT PLANT - Water Treatment Plant Pumps: Guidelines For Selection, Application, And Operation
January 1, 2017 - HI/HYDRAUL
A description is not available for this item.
SWRI WATER REPELLANT - CLEAR WATER REPELLENT FOR MASONRY
January 1, 1994 - SWRI

This comprehensive manual includes information on clear water repellent materials for both vertical and horizontal surfaces. Also included are a glossary, product comparisons, specifications, monograph and performance test criteria.

WATER TREATMENT PLANT - WATER TREATMENT PLANT DESIGN
AWWA
A description is not available for this item.
NSF WATER ADDITIVE SET - DRINKING WATER ADDITIVE SET - STANDARDS 60 AND 61
NSF
A description is not available for this item.
ASTM C1262/C1262M-26 - Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
June 1, 2026 - ASTM International

4.1 The procedure described in this test method is intended to determine the effects of freezing and thawing on SRW and related units in the presence of potable tap water or saline solution. 4.2 The procedure is not intended to provide a quantitative measure to determine an expected...

ASTM D4382-18(2026) - Standard Test Method for Barium in Water, Atomic Absorption Spectrophotometry, Graphite Furnace
May 1, 2026 - ASTM International

5.1 Barium ranks about sixth in order of abundance in nature; however, it is normally found in only trace quantities in drinking water. Consumption, inhalation, or absorption of 500?mg to 600?mg is considered fatal to human beings. Lower levels may result in disorders of the heart, blood...

ASTM E2111-26 - Standard Test Method to Evaluate the Bactericidal, Fungicidal, Mycobactericidal, and Sporicidal Potencies of Liquid Chemicals using Quantitative Carriers (Quantitative Carrier Test-Tier 1)
March 1, 2026 - ASTM International

5.1 This test method is fully quantitative and it also avoids any loss of viable organisms through wash off, making it possible to produce statistically valid data using many fewer test and control carriers than other quantitative methods based on most probable numbers (MPN). 5.2 The design of the...

ASTM D8606-26 - Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Modified Continuously Closed Cup (MCCCFP) Tester
May 1, 2026 - ASTM International

1.1 This test method covers the procedure for a finite flash point test, within the range of -25?°C to 90?°C, of liquid wastes using an MCCCFP tester. This test method is used in the determination of flash point of liquid wastes. Note 1: The connection of tap water or a cooling device...

ASTM D1687-17(2025) - Standard Test Methods for Chromium in Water
July 1, 2025 - ASTM International

1.1 These test methods cover the determination of hexavalent and total chromium in water. Section 34 on Quality Control pertains to these test methods. Three test methods are included as follows: Test Method Concentration Range Sections A-Photometric Diphenyl- carbohydrazide ?0.01?mg/L to 0...

ASTM D8574-25 - Standard Test Method for Determination of Select Pesticides and Herbicides in Water by Liquid Chromatography Tandem Mass Spectrometry (LC-MS/MS)
May 1, 2025 - ASTM International

1.1 This test method covers the determination of selected water-soluble pesticides and herbicides, including regulated carbamates and chlorinated acids in aqueous matrices, including ground water, surface water, finished drinking water, and wastewater, by cosolvation...

ASTM D3373-17(2025) - Standard Test Method for Vanadium in Water
July 1, 2025 - ASTM International

5.1 Vanadium can be found in waste that result from chemical cleaning of components in which the metal is alloyed. 5.2 National Pollutant Discharge Elimination Systems permits or other standards, or both, require monitoring pollutants in waste discharged onto the water shed of, or into,...

ASTM D3697-17(2025) - Standard Test Method for Antimony in Water
July 1, 2025 - ASTM International

1.1 This test method covers the determination of dissolved and total recoverable antimony in water by atomic absorption spectroscopy.2 1.2 This test method is applicable in the range from 1?μg/L to 15?μg/L of antimony. The range may be extended by less scale expansion or by dilution of the...

ASTM A74-26 - Standard Specification for Cast Iron Soil Pipe and Fittings
April 1, 2026 - ASTM International

This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial...

ASTM D3223-17(2025) - Standard Test Method for Total Mercury in Water
December 1, 2025 - ASTM International

5.1 The presence of mercury in industrial discharge, domestic discharge, and potable water is of concern to the public because of its toxicity. Regulations and standards have been established that require the monitoring of mercury in water. This test method provides an analytical...

Tap Water as a Hydraulic Pressure Medium
November 17, 2000 - CRC

"Showcases the beneftis and potential advantages of water hydraulics over oil-based media. Interweaves examples and excercises throughout the text to illustrate critical concepts, with helpful appendices on abbreviations, symbols, conversion factors, and water contaminants, and...

ASTM F1023-12(2025) - Standard Specification for Dispensers, Powdered Iced Tea
March 1, 2025 - ASTM International

This specification covers counter model, self-contained powdered iced tea dispensers. The tea dispensers shall be of two types, each working with a powdered concentrate that is mixed with potable tap water to give a finished drink. Type I is designed to work with pure tea and Type II...

ISO 14436 - Pulps — Standard tap water for drainability measurements — Conductivity 40 mS/m to 150 mS/m
March 1, 2010 - ISO

This International Standard describes the specification and preparation of standard tap water, of conductivity between 40 mS/m and 150 mS/m, for drainability measurements. This International Standard is applicable to all kinds of pulps. NOTE ISO 14487 describes the specification and...

ASTM A74-25 - Standard Specification for Cast Iron Soil Pipe and Fittings
August 15, 2025 - ASTM International

This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial...

Advertisement