loading
ASTM F1875-26 - Standard Test Method for Long-Term Fretting Corrosion Testing of Modular Implant Interfaces: Hip Femoral Modular Head-Bore / Cone Taper Junctions
June 1, 2026 - ASTM International

5.1 The modular bore and cone interfaces of total joint prostheses are subjected to loads that could result in micromotion and fretting corrosion at the bore and cone taper interface. Release of ionic and particulate products of fretting corrosion could result in increased wear of the...

ASTM C1824-16(2026) - Standard Test Method for Full Scale Bending Test of Spun Prestressed Concrete Bases for Tapered Steel Lighting Poles
June 1, 2026 - ASTM International

5.1 This test method is intended to provide the user with acceptable apparatus requirements and a prescribed procedure to determine the bending moment capacity of spun pre-stressed concrete bases for use with tapered steel poles. 5.2 The results of this test method are used as a basis for...

ASTM E960-93(2026) - Standard Specification for Laboratory Glass Beakers
June 1, 2026 - ASTM International

This specification provides standard dimensional requirements for glass beakers suitable for general laboratory use. The glass beakers are classified into types and sizes and are presented in details. The glass beaker types are: type I - low form with spout; type II - low form, with spout heavy...

ASTM D6846-02(2026) - Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
June 1, 2026 - ASTM International

4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it provides...

ASTM E911-98(2026) - Standard Specification for Glass Stopcocks with Polytetrafluoroethylene (PTFE) Plugs
June 1, 2026 - ASTM International

This specification covers dimensional interchangeability requirements of glass stopcocks with polytetrafluoroethylene (PTFE) plugs for use in ordinary laboratory and industrial applications. However, it does not cover the design characteristics of the stopcock-plug assembly nor the physical or...

ASTM F3067-26 - Standard Guide for Radial Loading of Balloon-Expandable and Self-Expanding Vascular Stents
May 1, 2026 - ASTM International

1.1 This document provides guidance for developing in vitro test methods for measuring the radial strength or collapse pressure of balloon-expandable vascular stents and chronic outward force of self-expanding vascular stents. 1.2 This guide is applicable to balloon-expandable and self-expanding...

ASTM C188-26 - Standard Test Method for Density and Relative Density of Hydraulic Cement
May 1, 2026 - ASTM International

This test method covers the determination of the density of hydraulic cement. Its particular usefulness is in connection with the design and control of concrete mixtures. The density of hydraulic cement is defined as the mass of a unit volume of the solids. The apparatus to be used is a Le...

ASTM F2009-25 - Standard Test Method for Determining the Axial Disassembly Force of Taper Connections of Modular Prostheses
September 15, 2025 - ASTM International

4.1 This test method helps to assess the axial locking force of a modular taper. Some types of devices that can utilize this type of connection are the modular shoulder and modular hip prostheses. Additional means of evaluating the locking mechanisms of tapers can be appropriate,...

ASTM F1498-25 - Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
December 1, 2025 - ASTM International

1.1 This specification establishes requirements for dimensions and gaging of taper pipe threads used on threaded plastic pipe and fittings. 1.2 Threads meeting this specification shall only be used on those plastic materials deemed suitable by the manufacturer. 1.3 Specialty threads or...

ASTM B210/B210M-26 - Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
April 1, 2026 - ASTM International

This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose. The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot (cast in hollow form or pierced) and extruded by the use of the die and mandrel...

ASTM C1957/C1957M-25 - Standard Practice for Onsite Exfiltration Acceptance Testing of Precast Concrete Water and Wastewater Structures
December 1, 2025 - ASTM International

5.1 This is not a routine test. The values recorded are applicable only to the liquid holding structure being tested and at the time of testing. 5.2 Test times given in Table 1 are for prismatic volumes only. Test times for non-prismatic volumes, such as structures with tapered walls or...

ASTM F3525/F3525M-26 - Standard Specification Fabricated Fittings of Crosslinkable Polyethylene (CX-PE)
February 1, 2026 - ASTM International

1.1 This specification establishes requirements for fabricated fittings intended for use with outside-diameter controlled CX-PE pipe and tubing. These fittings are manufactured by heat-fusion joining shape-modified CX-PE components prepared from pipe, molded fittings, sheet, billet, or block....

ASTM F2942-25 - Standard Guide for in vitro Axial, Bending, Torsional, and Compression Durability Testing of Vascular Stents and Vascular Stent-Grafts
October 1, 2025 - ASTM International

1.1 This guide includes four separate cyclic deformation durability guides related to vascular stents and vascular stent-grafts: bending, axial, torsional, and compression. 1.2 This guide does not address whether a specific mode of durability testing is relevant for a particular vascular stent and...

ASTM E1403-97(2025) - Standard Specification for Laboratory Glass Boiling Flasks
July 1, 2025 - ASTM International

This specification provides standard dimensional requirements for flat-bottom and round-bottom glass boiling flasks. Boiling flasks shall be in the following types: type I - flat bottomed: class 1 - tooled top, long neck; class 2 - ring neck, long neck; class 3 - ring neck, long neck, wicker...

ASTM A733-25 - Standard Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples
September 1, 2025 - ASTM International

This specification covers welded and seamless carbon steel and austenitic stainless steel pipe nipples. The mechanical requirements stated that, pipe nipples shall be made from new, hydrostatic tested or NDE-tested pipe, pipe and nipples shall be threaded on both ends with NPT taper pipe...

ASTM D5685-25 - Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings
July 1, 2025 - ASTM International

This specification covers "fiberglass" (glass-fiber-reinforced thermosetting-resin) pressure pipe fittings for use with filament wound or centrifugally cast fiberglass pipe. The fibreglass fittings are defined by type, grade, class, category, and pressure rating: type 1 - filament-wound fittings,...

ASTM E1293-02(2025) - Standard Specification for Glass Measuring Pipets
July 1, 2025 - ASTM International

This specification covers requirements of precision (Class A) and general purpose (Class B) grade glass measuring pipets used for volume measurement of liquids. Pipets covered by this specification may be of the standard taper tip type (Style 1) or of the long taper tip type (Style...

ASTM E1404-94(2025) - Standard Specification for Laboratory Glass Conical Flasks
July 1, 2025 - ASTM International

This specification provides standard dimensional requirements for glass conical flasks suitable for general laboratory use. Conical flasks (Erlenmeyer) shall be classified into four types which are divided into classes. Type I is for general purpose with graduated scale and shall be designated into...

ASTM C1804-20(2025) - Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles
June 1, 2025 - ASTM International

This specification covers spun cast prestressed concrete bases used in tapered steel lighting poles. It provides requirements for acceptability of spun prestressed concrete bases produced in accordance with this specification, materials, bending test procedures, tolerances, and drawings. The...

ASTM E675-02(2024) - Standard Specification for Interchangeable Taper-Ground Stopcocks And Stoppers
November 1, 2024 - ASTM International

The specification provides the standard dimensional requirements for obtaining, within practical limits, interchangeability in stopcocks and stoppers for ordinary laboratory and industrial applications. It solely covers ground surfaces dimensional interchangeability, and does not involve design...

Advertisement