loading
ASTM D2582-21 - Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
May 1, 2021 - ASTM International

4.1 The puncture-propagation of tear test measures the resistance of a material to snagging, or more precisely, to dynamic puncture and propagation of that puncture resulting in a tear. Failures due to snagging occur in a variety of end uses, including industrial bags, liners, and tarpaulins...

DS/EN 12641-2 - Intermodal loading units and commercial vehicles – Tarpaulins – Part 2: Minimum requirements for curtainsiders
December 16, 2019 - DS

This document specifies minimum requirements for the strength and attachment of tarpaulins used as curtainsiders on intermodal loading units and commercial vehicles. NOTE - The described tarpaulins according to this document only work for load securing with a body according to...

DS/EN 12641-1 - Intermodal loading units and commercial vehicles – Tarpaulins – Part 1: Minimum requirements
December 16, 2019 - DS

This document specifies minimum requirements for the strength and attachment of tarpaulins used on swap bodies and utility vehicles for road and road/rail combined (intermodal transport) traffic.

BS EN 12641-1 - Intermodal loading units and commercial vehicles - Tarpaulins Part 1: Minimum requirements
December 31, 2019 - BSI
A description is not available for this item.
ASTM D751 - Standard Test Methods for Coated Fabrics
May 1, 2019 - ASTM

These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. The scope of each of these test methods appears in the section in which the test method is described. The values stated in SI units are to be regarded as the standard...

J3082_201908 - Auxiliary Two-Conductor Electrical Power Connector for Truck-Trailer High-Power Jumper Cable
August 20, 2019 - SAE International

This SAE Standard provides the minimum requirements for high-power, two-conductor jumper cable plug and receptacle for truck-trailer jumper cable systems. It includes the test procedures, design, and performance requirements. This document covers receptacles rated 12 VDC nominal and at more than 30...

ASTM D751-19 - Standard Test Methods for Coated Fabrics
May 1, 2019 - ASTM International

1.1 These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. 1.2 The scope of each of these test methods appears in the section in which the test method is described. 1.3 The test methods appear in the following sections:...

ASTM E2278-13(2019) - Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage
September 1, 2019 - ASTM International

4.1 General-CCPs can effectively be used to reclaim surface mines (5-10). First, CCPs are ideally suited for use in numerous reclamation applications. Any type of CCP may be evaluated for use in mine reclamation. Project specific testing is necessary to ensure that the CCPs selected for use on a...

ASTM E2243-13(2019) - Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation
September 1, 2019 - ASTM International

4.1 Significance and Use-CCPs can be effective materials for use for reclamation of surface mines. Following are key scenarios in which CCPs may be utilized beneficially in a mined setting: Structural fill Road construction Soil modification or amendment for revegetation (5-9) Isolation of acid...

ASTM D2582-16 - Standard Test Method for Puncture-Propagation Tear Resistance of Plastic Film and Thin Sheeting
April 1, 2016 - ASTM International

4.1 The puncture-propagation of tear test measures the resistance of a material to snagging, or more precisely, to dynamic puncture and propagation of that puncture resulting in a tear. Failures due to snagging occur in a variety of end uses, including industrial bags, liners, and tarpaulins...

SSPC GUIDE 7 - GUIDE TO THE DISPOSAL OF LEAD-CONTAMINATED SURFACE PREPARATION DEBRIS
July 9, 2015 - SSPC

This guide provides information regarding handling, testing, and disposal of solid debris generated during preparation of surfaces previously painted with lead-containing paint. This guide is based on U.S. federal regulations only. States or other local jurisdictions may have requirements that are...

JIS Z 1503 - Tarpaulin Paper
May 1, 1995 - JSA
A description is not available for this item.
ASTM E2278-13 - Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage
November 15, 2013 - ASTM International

4.1 General-CCPs can effectively be used to reclaim surface mines (5-10). First, CCPs are ideally suited for use in numerous reclamation applications. Any type of CCP may be evaluated for use in mine reclamation. Project specific testing is necessary to ensure that the CCPs selected for use on a...

ASTM E2243-13 - Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation
October 1, 2013 - ASTM International

4.1 Significance and Use-CCPs can be effective materials for use for reclamation of surface mines. Following are key scenarios in which CCPs may be utilized beneficially in a mined setting: Structural fill Road construction Soil modification or amendment for revegetation (5-9) Isolation of acid...

GME TM 281100 - TARPAULIN MATERIAL
GME
A description is not available for this item.
ASTM D751-06(2011) - Standard Test Methods for Coated Fabrics
November 1, 2011 - ASTM International

1.1 These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. 1.2 The scope of each of these test methods appears in the section in which the test method is described. 1.3 The test methods appear in the following sections:...

A-A-55235 - TARPAULIN, COTTON DUCK, 20 FEET BY 20 INCHES
March 8, 2000 - NPFC

This document covers a 20 foot by 20 inch tarpaulin. The tarpaulin is designed to cover the junction where two shelters are placed end to end.

Advertisement