5.1 The high-temperature capabilities of advanced ceramics are a key performance benefit for many demanding engineering applications. In many of those applications, advanced ceramics will have to perform across a broad temperature range. The thermal expansion, thermal...
1.1 This practice describes the determination of thermal endurance, thermal index, and relative thermal index for organic materials using the Arrhenius activation energy generated for thermal decomposition measured by thermogravimetry. 1.2 This practice is generally...
5.1 Thermogravimetry provides a rapid method for determining the thermal decomposition and reaction mass change of a material. 5.2 This test method is useful in detecting potentially hazardous reactions and in estimating the temperatures at which these reactions occur. This test method is...
5.1 This practice is designed to compare related materials under controlled conditions and their ability to maintain a minimum amount of thermal conductance. Test results should be correlated with field results in order to predict heat transfer properties in particular applications. 5.2 This...
1.1 This test method describes the temperature calibration of a dynamic mechanical analyzer using thermal lag over the temperature range of -100 °C to 300 °C. 1.2 This standard may be compared to Test Methods E1867. 1.3 The values stated in SI units are to be regarded as standard. No other...
1.1 This test method describes the determination of the thermal conductivity in the range from 0.08 W/m·K to 10.0 W/m·K of filled and unfilled thermoplastics, thermosets, and rubbers over a temperature range from -40?°C to 450?°C. 1.2 The SI units are the standard. 1.3 This standard does not...
1.1 This practice is intended to assist in size selection of work uniforms for fire and rescue services personnel and workers who have the potential to be exposed to thermal hazards. Work uniform ensembles consist of a shirt and trouser apparel combination. 1.1.1 This practice does not apply...
1.1 Practice D7897 applies to simulation of the effects of field exposure on the solar reflectance and thermal emittance of roof surface materials including but not limited to field-applied coatings, factory-applied coatings, single-ply membranes, modified bitumen products, shingles, tiles,...
1.1 This practice covers procedures for detecting the sources of gas leaking at the rate of 1?×?10 -5 Pa m3/s [1?×?10-4 std cm3/s] or greater. The tests may be conducted on any object that can be pressurized with a tracer gas that is detectable by a thermal conductivity detector. The test...
5.1 Thermal stability characterizes physical and chemical property changes which may adversely affect an oil's lubricating performance. This test method evaluates the thermal stability of a hydraulic oil in the presence of copper and steel at 135?°C. No correlation of the test to...
1.1 Purpose-Practices to be employed for the radiographic examination of materials and components with thermal neutrons are outlined herein. They are intended as a guide for the production of neutron radiographs that possess consistent quality characteristics, as well as aiding the user to...
5.1 The determination of the total volume?percent of saturates, olefins, and aromatics in petroleum fractions is important in characterizing the quality of petroleum fractions as gasoline blending components and as feeds to catalytic reforming processes. This information is also important in...
3.1 This test method defines the thermal expansion of porcelain enamel and glaze frits by the interferometric method. This determination is critical in avoiding crazing (cracking) of these glass coatings due to mismatching of the thermal expansion between the coating and substrate...
1.1 This guide covers information on selection of insulation materials, systems design, application methods, protective coverings, guarantees, inspection, testing, and maintenance of thermal insulation primarily for industrial applications in a temperature range of -320 to 1200°F (-195.5 to...
4.1 Determination of the hydro-thermal area stability of Wet Blue provides information concerning the efficacy of the tanning process as well as the adequacy of the Wet Blue for intended end use applications where area stability is a particular requirement. Relative area stability of...
4.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can affect the PET quality (such as contribute to fiber breaks), the polymerization process, and 4-CBA imparts coloration to the polymer due to thermal instability. 4.2 Determining the...
1.1 This test method rates the non-steady state thermal resistance or insulating characteristics of flame resistant clothing materials subjected to a continuous, standardized radiant heat exposure. 1.1.1 This test method is not applicable to clothing materials that are not flame resistant....
5.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can slow down the polymerization process; and 4-CBA is also imparting coloration to the polymer due to thermal instability. 5.2 Determining the amount of 4-CBA and p-TOL remaining from...
5.1 The presence of 4-CBA and p-TOL in PTA used for the production of polyester is undesirable because they can slow down the polymerization process; and 4-CBA is also imparting coloration to the polymer due to thermal instability. 5.2 Determining the amount of 4-CBA and p-TOL remaining from...
1.1 This test method applies to the determination of hydrogen in nuclear-grade uranium oxide powders and pellets to determine compliance with specifications. Gadolinium oxide (Gd2O3) and gadolinium oxide-uranium oxide powders and pellets may also be analyzed using this test method. 1.2 This...