loading
ASTM A1082/A1082M-26 - Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications
July 1, 2026 - ASTM International

This specification covers high strength stainless steel bolting for special purpose applications such as pressure vessels. Several grades of precipitation-hardened and duplex (ferritic-austenitic) stainless steels are covered. Selection will depend upon design, service conditions, mechanical...

ASTM A1014/A1014M-26 - Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service
July 1, 2026 - ASTM International

This specification covers a precipitation hardening bolting material (UNS N07718) for high temperature service. The alloy shall be multiple melted using consumable electrode practice in the remelt cycle or shall be induction melted under vacuum. Requirements for solution treatment, precipitation...

ASTM D6557-26 - Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils
June 1, 2026 - ASTM International

1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 The values stated in SI units are to be...

ASTM E1118/E1118M-26 - Standard Practice for Acoustic Emission Examination of Reinforced Thermosetting Resin Pipe (RTRP)
May 1, 2026 - ASTM International

5.1 The AE examination method detects damage in RTRP. The damage mechanisms detected in RTRP are as follows: resin cracking, fiber debonding, fiber pullout, fiber breakage, delamination, and bond or thread failure in assembled joints. Flaws in unstressed areas and flaws which are...

ASTM F606/F606M-26a - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
May 15, 2026 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the...

ASTM F606/F606M-26 - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
May 1, 2026 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the...

ASTM F432-19(2026) - Standard Specification for Roof and Rock Bolts and Accessories
May 1, 2026 - ASTM International

This specification covers the chemical, mechanical, and dimensional requirements for roof and rock bolts and accessories. Addressed in this specification are double-end threaded and slotted steel bars; fully grouted bolts and threaded bars; mechanical anchorage devices used for point...

ASTM E1685-20(2026) - Standard Practice for Measuring the Change in Length of Bolts Using the Ultrasonic Pulse-Echo Technique
April 1, 2026 - ASTM International

1.1 This practice covers a procedure for measuring changes in length of threaded bolts using the ultrasonic pulse-echo technique. 1.2 This procedure is normally intended for metal bolting 6.3 mm or more in nominal diameter with effective length-to-diameter ratios of 2:1 or greater. 1.3 The...

ASTM D2513-26a - Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
April 1, 2026 - ASTM International

This specification covers the requirements and test methods for material, dimensions, hydrostatic burst strength, tensile strength, chemical resistance, sustained pressure, heat fusion, and impact resistance of plastic pipes, tubing, and fittings used for direct burial and reliner applications in...

ASTM A354-26 - Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners
March 1, 2026 - ASTM International

1.1 This specification ?covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, threaded rod, and other externally threaded fasteners 4 in. and under in diameter for application at normal atmospheric temperatures, where high strength is...

ASTM F468-23(2026) - Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
March 1, 2026 - ASTM International

1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs 0.250 to 1.500 in., socket head cap screws (including socket head cap, button head and flat countersunk head configurations) with nominal thread 0.06 (size 0) through 1.500 in....

ASTM A74-26 - Standard Specification for Cast Iron Soil Pipe and Fittings
April 1, 2026 - ASTM International

This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method...

ASTM F467-24(2026) - Standard Specification for Nonferrous Nuts for General Use
March 1, 2026 - ASTM International

This specification covers the requirements for commercial wrought nonferrous nuts in nominal thread diameters M6 to M36 inclusive in a number of alloys in common use and intended for general service applications. Materials shall be tested and shall conform to the chemical composition,...

ASTM D8617-26 - Standard Test Method for Evaluation of Automotive Engine Oils for Soot-Viscosity Performance in a Cummins ISB Medium-Duty Diesel Engine
March 1, 2026 - ASTM International

1.1 This test method, commonly referred to as the Cummins ISB Viscosity Test, covers the utilization of a 5.9?L diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to soot induced viscosity increase. 1.2 The values stated in SI units are to be...

ASTM F1428-26 - Standard Specification for Aluminum Particle-Filled Basecoat/Organic or Inorganic Topcoat, Corrosion Protective Coatings for Fasteners
March 15, 2026 - ASTM International

This specification covers corrosion-resistant coating consisting of an inorganic aluminum particle-filled basecoat and an organic or inorganic topcoat. The basecoat is a water-dilutable slurry containing aluminum particles dispersed in a liquid binder of chromate/phosphate compounds. The organic...

ASTM E2111-26 - Standard Test Method to Evaluate the Bactericidal, Fungicidal, Mycobactericidal, and Sporicidal Potencies of Liquid Chemicals using Quantitative Carriers (Quantitative Carrier Test-Tier 1)
March 1, 2026 - ASTM International

5.1 This test method is fully quantitative and it also avoids any loss of viable organisms through wash off, making it possible to produce statistically valid data using many fewer test and control carriers than other quantitative methods based on most probable numbers (MPN). 5.2 The design of the...

ASTM A563/A563M-26 - Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric)
March 1, 2026 - ASTM International

1.1 This specification covers chemical, mechanical, and dimensional requirements for eleven grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts. Note 1: See Appendix X1 for guidance on suitable application of...

ASTM F1498-25 - Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
December 1, 2025 - ASTM International

This specification establishes requirements for dimensions and gaging of taper pipe threads used on threaded plastic pipe and fittings. The type of pipe threads are designated by specifying in sequence the nominal pipe size, number of threads per inch, and the...

ASTM D6193-16(2025) - Standard Practice for Stitches and Seams
November 1, 2025 - ASTM International

4.1 Seam engineering, the determination of the best stitch type, seam configuration, and thread type which should be used for a particular assembly, requires a thorough knowledge of many variables. The improper selection of any one component can result in failure of the sewn junction, and...

ASTM F480-25 - Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
December 1, 2025 - ASTM International

This specification covers water well casing pipe and couplings made from thermoplastic materials in standard dimension ratios (SDR), SCH 40 and SCH 80. Well casing is produced in either plain end, belled end, or threaded, and is used for water wells, ground water monitoring, leak detection,...

Advertisement