loading
ASTM F2199-26 - Standard Test Method for Determining Dimensional Stability and Curling Properties of Resilient Flooring after Exposure to Heat
August 1, 2026 - ASTM International

4.1 The final appearance of an installed floor depends upon several factors. These include but are not limited to size and squareness in the case of tiles/planks, the quality of joint cut, the quality and preparation of the subfloor and the skill of the installer. Long term appearance of the...

ASTM C1895-26 - Standard Test Method for Determination of Mohs Scratch Hardness
June 1, 2026 - ASTM International

1.1 This test method covers the procedures to determine the Mohs scratch hardness of ceramic tile, glass tile, and other hard surfaces. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units...

ASTM D7897-26 - Standard Practice for Laboratory Soiling and Weathering of Roofing Materials to Simulate Effects of Natural Exposure on Solar Reflectance and Thermal Emittance
July 1, 2026 - ASTM International

1.1 Practice D7897 applies to simulation of the effects of field exposure on the solar reflectance and thermal emittance of roof surface materials including but not limited to field-applied coatings, factory-applied coatings, single-ply membranes, modified bitumen products, shingles, tiles,...

ASTM F3008-13(2025) - Standard Specification for Cork Floor Tile
November 15, 2025 - ASTM International

1.1 This specification covers requirements for the compound and physical characteristics of cork floor tile. This standard specifies the requirements for cork floor coverings made from agglomerated composition cork supplied in tile form, which are designed to be used with a factory...

ASTM C1713-26 - Standard Specification for Mortars for the Repair of Historic Masonry
June 1, 2026 - ASTM International

1.1 This specification covers mortar for the repair of masonry that was constructed with methods and materials that pre-date the origination of current standards of construction that are compatible with it. The mortar may be used for non-structural purposes such as repointing of the masonry, or for...

ASTM F3191-26 - Standard Practice for Field Determination of Substrate Water Absorption (Porosity) for Substrates to Receive Resilient Flooring
May 15, 2026 - ASTM International

1.1 This practice covers the determination of whether or not a substrate surface, in lieu of written instruction from a product manufacturer, is considered porous or non-porous prior to the installation of resilient flooring materials. 1.2 Although carpet tiles, carpet, wood flooring,...

ASTM C844-26 - Standard Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
May 1, 2026 - ASTM International

1.1 This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters. 1.2 Gypsum veneer base shall not be used as a base for direct adhesive application of ceramic, metal, or plastic tile in areas exposed to abnormal...

ASTM F511-17(2025) - Standard Test Method for Quality of Cut (Joint Tightness) of Resilient Floor Tile
October 1, 2025 - ASTM International

3.1 Installations of resilient floor tile require tight joints if satisfactory appearance is to result. The quality of cut of resilient tile is determined by this test method.

ASTM F1066-25 - Standard Specification for Vinyl Composition Floor Tile
June 15, 2025 - ASTM International

This specification covers vinyl composition floor tile with either smooth or embossed surfaces. Vinyl composition tile shall conform to the materials, color, pattern, wearing surface, size, thickness, and squareness indicated in this specification. The material shall be tested for...

ASTM D1779-98(2026) - Standard Specification for Adhesive for Acoustical Materials
January 1, 2026 - ASTM International

1.1 This specification covers an adhesive for bonding prefabricated acoustical materials to the inside walls and ceilings of rooms in buildings. This adhesive is required to maintain a tensile adhesion (bond strength) of not less than 3.45 × 104 dynes/cm2 (1/2 lb/in.2) for a long period of time...

ASTM D8569-26 - Standard Practice for Surface Sampling of Non-Volatile and Semi-Volatile Organic Chemicals for Worker Protection
January 1, 2026 - ASTM International

5.1 This practice is intended for the collection of samples on surfaces for the subsequent measurement of target nonvolatile and semi-volatile organic chemicals. The practice is meant for use in the collection of samples that are of interest in hazard evaluation, exposure assessment, risk...

ASTM C1232-26 - Standard Terminology for Masonry
January 1, 2026 - ASTM International

1.1 This standard incorporates terms and definitions of terms used in standards under the jurisdiction of Committee C15 on Masonry - Manufactured Masonry Units, Mortars, and Grouts. 1.2 This standard incorporates terms and definitions of terms associated with the standards specific to clay masonry...

ASTM F3781-25 - Standard Test Method for Measurement of the Fracture Resistance of a Modular Resilient Flooring's Profiled Edge(s) to an Applied Vertical Force
November 1, 2025 - ASTM International

4.1 Modular flooring having profiled edges, installed as a floating floor can provide a quick and easy installation system. The product is held together by the interlocking profiled edges. If the profiled edges are too brittle, over flexed, etc. they can be susceptible to fracture, which can then...

ASTM E2356-26 - Standard Practice for Comprehensive Building Asbestos Surveys
February 1, 2026 - ASTM International

4.1 Management of asbestos-containing materials in buildings and facilities requires knowledge of the location, type, quantity, and condition of the material. The more complete and accurate the information available, the more appropriate and cost-effective are the control measures used to reduce...

ASTM E2458-26 - Standard Practices for Bulk Sample Collection and Swab Sample Collection of Visible Powders Suspected of Being Biological Agents and Toxins from Nonporous Surfaces
January 15, 2026 - ASTM International

4.1 These practices should be used only to collect visible samples that are suspected biological agents and toxins and have been field screened as defined by the FBI-DHS-HHS/CDC Coordinated Document for explosive hazard, radiological hazard, and other acute chemical hazards. 4.2 These practices...

ASTM D1970/D1970M-25 - Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection
December 1, 2025 - ASTM International

1.1 This specification covers polymer modified bituminous sheet materials intended for use as underlayment on roof eaves, or valleys, or both, to prevent leakage of shingle, tile, or metal roofs from water back-up due to ice dams. 1.2 These underlayment sheets have a sticky adhesive layer...

ASTM F150-25 - Standard Test Method for Electrical Resistance of Conductive and Static Dissipative Resilient Flooring
November 15, 2025 - ASTM International

1.1 This test method covers the determination of electrical conductance or resistance of resilient flooring either in tile or sheet form, for applications such as hospitals, computer rooms, clean rooms, access flooring, munition plants, or any other environment concerning personnel-generated...

ASTM F1700-25 - Standard Specification for Solid Vinyl Floor in Modular Format such as Tile(s) or Plank(s)
July 1, 2025 - ASTM International

This specification establishes the material and performance characteristics that determine serviceability and recommended applicability of solid vinyl floor tiles intended for use in commercial, light commercial, and residential buildings. Floor tiles shall be classified as Class I...

ASTM C67/C67M-25 - Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile
August 1, 2025 - ASTM International

These test methods cover procedures for the sampling and testing of brick and structural clay tile. The tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate or absorption, and determination of...

ASTM C636/C636M-19(2025) - Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-In Panels
August 1, 2025 - ASTM International

This practice covers the standard procedures for the installation of metal ceiling suspension systems for acoustical tile and lay-in panels. Here, specifications are provided for the installation of individual components such as hangers, carrying channels, main runners, cross runners,...

Advertisement