5.1 Lubricants can contain basic constituents that are present as additives. The relative amount of these materials can be determined by titration with acids. The base number is a measurement of the amount of basic substances in the oil under the conditions of the testing procedure. 5.2 A...
4.1 Any residual fatty acid and esters (FA&E) should be present only at very low levels in purified glycerine. 4.2 This procedure requires the addition of a measured volume of sodium hydroxide, in excess of the amount actually needed to react with FA&E in the glycerine sample. After boiling, the...
1.1 This test method covers the determination of free acids and glycol esters in glycols by titration. 1.2 This test method is typically used on glycols used for the manufacture of engine coolant. It cannot be used on formulated engine coolant. The inhibitors will interfere with the...
5.1 The total apparent water in engine coolant concentrate as determined by Karl Fischer titrations consists of the following: (1) water present in the original glycol base; (2) water added (for example, inhibitor solutions); (3) water of hydration of inhibitors (for example, Na2B4O7·5H2O);...
5.1 New and used petroleum products can contain basic constituents that are present as additives. The relative amount of these materials can be determined by titration with acids. The base number is a measure of the amount of basic substances in the oil always under the conditions of the...
1.1 This test method covers the determination of basic constituents in petroleum products by titration with perchloric acid in glacial acetic acid. 1.2 Procedures A and B use different titration solvent volumes and sample weights. Note 1: A round robin on a series of new and used oils...
3.1 This test method is intended for the determination of organically combined sulfuric anhydride in sulfated oils.
5.1 This test method is useful as an internal quality control tool, and for use in development or research work on industrial aromatic hydrocarbons and related materials. This test method gives a broad indication of olefinic content. It will not differentiate between the types of aliphatic...
1.1 This test method is used to determine the number of silanol groups on the surface of silica by titration according to a method as developed by Sears. This test method is suitable for characterizing rubber-grade silicas. 1.2 Units-The values stated in SI units are to be regarded as the...
This specification covers the requirements for HFC-125 (pentafluoroethane, C2HF5) as a fire-fighting medium. It does not however address the fire-fighting equipment or hardware that employs HFC-125, the conditions of employing such equipment like hand helds, fixed installations, etc., or the...
1.1 These test methods cover the chemical analysis of glass sands. They are useful for either high-silica sands (99?%+?silica (SiO2)) or for high-alumina sands containing as much as 12?% to 13?% alumina (Al2O3). Generally nonclassical, these test methods are rapid and accurate. They include the...
1.1 These test methods cover procedures for the chemical and mass spectrometric analysis of nuclear-grade gadolinium oxide powders to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Carbon by Direct Combustion-Thermal Conductivity...
5.1 This test method is suitable for setting specifications, for use as an internal quality control tool, and for use in development or research work on industrial aromatic hydrocarbons and related material. This test method gives a broad indication of olefinic content. It does not differentiate...
4.1 MBT is commonly used in rubber compounding as a curing accelerator for rubber and latex products. The determination of MBT in cured rubber is important to assess the risk of a release of this hazardous substance when rubber is in prolonged contact with human skin or mucous membranes. 4.2...
5.1 This laboratory test method measures thermal combustion properties of materials (1-9). 5.2 The test uses controlled thermal and thermal-oxidative decomposition of specimens and thermal oxidation of the specimen gases as they are released from the specimen to simulate the condensed and gas phase...
1.1 These practices describe means for calibrating ambient, workplace or indoor ozone monitors, using transfer standards. 1.2 These practices describe five types of transfer standards: Practice A-Analytical instruments, Practice B-Boric acid potassium iodide (BAKI) manual analytical procedure,...
5.1 This laboratory test method measures thermal combustion properties of materials (1-9). 5.2 The test uses controlled thermal and thermal-oxidative decomposition of specimens and thermal oxidation of the specimen gases as they are released from the specimen to simulate the condensed and gas phase...
5.1 This test method can be used for evaluating performance of commercially available anion-exchange materials regardless of the basic strength of the ion exchange groups. When previous operating history is known, a good interpretation of resin fouling or malfunction can be obtained by comparison...
4.1 The approximate acidity of used electrical insulating oils is an estimate of the total acid value of the oil. As acid values increase, oil quality decreases. This is usually due to oxidation of the oil while in service. In general, acidic by-products produce increased dielectric loss, increased...
4.1 This test method is based on the cold oxidation of the glycerol by sodium metaperiodate in a strong acidic medium. Formaldehyde and formic acid are produced in this reaction and the latter is used to measure the glycerol content by titration with standard sodium hydroxide solution, to a...
Narrow Your Results