loading
EIA TRADE DIRECTORY M - EIA TRADE DIRECTORY & MEMBERSHIP LIST
EIA
A description is not available for this item.
TRADE EXPERT - MONTH - IHS IMPORT REGULATIONS - MONTHLY
IHS
A description is not available for this item.
TRADE EXPERT - QUARTER - IHS IMPORT REGULATIONS - QUARTERLY
IHS
A description is not available for this item.
IPS STANDARDS AND TRADE - IP-Shield: Standards and Trade (Standards Education)
IPS

What is the role of standards in the global marketplace? The link between standards and international trade is examined in this course, which will: Demonstrate the importance of standards to global trade Describe standards harmonization and illustrate the concept, using examples...

EIA FOREIGN TRADE NM - EIA ELECTRONIC FOREIGN TRADE REPORT - NON MEMBER
EIA
A description is not available for this item.
EIA ELEC FOREIGN TRADE M - EIA ELECTRONIC FOREIGN TRADE REPORT - MEMBERS
EIA
A description is not available for this item.
EIA ELEC FOREIGN TRADE NM - EIA ELECTRONIC FOREIGN TRADE REPORT - NON MEMBERS
EIA
A description is not available for this item.
EIA FOREIGN TRADE M - EIA ELECTRONICS FOREIGN TRADE REPORT - MEMBER
EIA
A description is not available for this item.
ASTM D1119-22(2026) - Standard Test Method for Percent Ash Content of Engine Coolants
August 1, 2026 - ASTM International

1.1 This test method covers the determination of ash content after ignition of commercial engine coolants and antirusts, as packaged or after use. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does...

ASTM D2847-22(2026) - Standard Practice for Testing Engine Coolants in Car and Light Truck Service
August 1, 2026 - ASTM International

1.1 This practice covers an updated procedure for evaluating corrosion protection and performance of an engine coolant in passenger car, light truck service that closely imitates current vehicle and engine manufacturers' practices. Note 1: Coolant evaluation in vehicle service may require...

ASTM D6752/D6752M-26 - Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method
August 1, 2026 - ASTM International

1.1 This test method covers the determination of bulk specific gravity of compacted asphalt mixtures by the vacuum sealing method. 1.2 This method can be used for compacted cylindrical and cubical laboratory and field asphalt mixture specimens. 1.3 The bulk specific gravity of the compacted asphalt...

ASTM F2199-26 - Standard Test Method for Determining Dimensional Stability and Curling Properties of Resilient Flooring after Exposure to Heat
August 1, 2026 - ASTM International

1.1 This test method covers the determination of the change in linear dimensions of resilient floor tile/plank products after exposure to heat and reconditioning to ambient temperature. 1.2 This test method allows one to also measure curling that can occur after a specimen has been exposed to heat...

ASTM D1123-22a(2026) - Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method
August 1, 2026 - ASTM International

1.1 These test methods cover the determination of the water present in new or unused glycol-based coolant concentrates using a volumetric (Test Method A) or an automatic coulometric titrator procedure (Test Method B). 1.2 Many carbonyl compounds react slowly with the Fischer reagent, causing a...

ASTM D1177-22(2026) - Standard Test Method for Freezing Point of Aqueous Engine Coolants
August 1, 2026 - ASTM International

1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory. Note 1: Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases...

ASTM F1488-26a - Standard Specification for Coextruded Composite Pipe
August 1, 2026 - ASTM International

1.1 This specification covers coextruded composite pipe, intended for non-pressure gravity flow drain waste or vent (DWV) service, or plastic underdrain service, or electrical or comunications conduit service produced by a coextrusion die system, in which the concentric layers are formed and...

ASTM F3115/F3115M-26a - Standard Specification for Structural Durability for Small Aeroplanes
August 1, 2026 - ASTM International

1.1 This specification addresses the airworthiness requirements related to structural durability for the design of small aeroplanes. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Levels 1 through 4 Normal...

ASTM F3519-21(2026)e1 - Standard Guide for Establishing a Reporting Structure for Exoskeleton Analysis
July 15, 2026 - ASTM International

1.1 This guide provides a structure for exoskeleton manufacturers to document their analysis. Furthermore, this guide should be used in conjunction with Practice F3474, Guide F3518, Guide F3688, and other future documents. 1.2 This standard does not purport to address all of the safety concerns, if...

ASTM D1238-26 - Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
July 15, 2026 - ASTM International

1.1 This test method covers the determination of the rate of extrusion of molten thermoplastic resins using an extrusion plastometer. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with...

ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

1.1 This specification covers requirements, test methods, and marking requirements for system components when tested with nominal SDR9 crosslinked polyethylene (PEX) tubing as a system. Systems are intended for 100 psi (0.69 MPa) water service up to and including a maximum working temperature of...

Advertisement