1.1 This specification covers flexible, non-exposed glass-bead lens and microprismatic, retroreflective sheeting designed for use on traffic control signs, delineators, barricades, and other devices. This specification does not address inks, overlays, or other imaging methods that may be...
1.1 This specification covers the requirements for segmental concrete paving slabs used for construction of pedestal-set applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-presse
1.1 This consumer safety specification covers the establishment of performance requirements and corresponding test methods used to minimize the hazards to users of electric-powered scooters for rent or lease by multiple users but not individually owned units. For example, electric-powered scooters...
1.1 This specification describes the required properties and test methods for a one or two-component, cold liquid-applied elastomeric-type membrane comprised of silyl-terminated polyether polymer, silyl-terminated polyurethane polymer, or a blend of the two polymers for waterproofing building decks...
4.1 Adequate coating thickness (mil thickness) is necessary to protect polyurethane foam from the effects of ultraviolet degradation. This guide outlines general procedures for sampling and measuring the coating thickness by using slit or core samples. 4.2 Thickness of individual lifts of sprayed...
1.1 This specification covers the requirements for segmental concrete paving slabs manufactured for construction of pedestrian and roof applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-presse
1.1 This practice covers software development, validation and verification practices for software that is part of an unmanned aircraft system (UAS), including its associated elements. It may also be used by third-party service providers, including UAS Traffic Management (UTM) service...
4.1 Geomembranes are used as impermeable barriers to prevent liquids from leaking from landfills, ponds, and other containment facilities. The liquids may contain contaminants that, if released, can cause damage to the environment. Leaking liquids can erode the subgrade, causing further damage....
1.1 This specification covers the requirements for aerial work that apply to all classes of aircraft that meet the requirements for Light Sport Category Aircraft. 1.2 Aerial work included within this specification shall be limited to the following: 1.2.1 Glider towing; 1.2.2 Banner towing; 1.2.3...
1.1 This test method covers a measurement of the wet retroreflective (RL-2) properties of horizontal pavement marking materials, such as traffic stripes and road surface symbols. A standardized method utilizing a standardized continuous wetting device and a portable retroreflectometer is...
4.1 This practice should be used in conjunction with a surface and subsurface site investigation to delineate a recommended field area that is adequate for any septic system that can reasonably be anticipated for the site. If actual design results in a smaller field area, the boundaries can be...
4.1 This guide is intended to apply in conjunction with applicable end-product specific performance or design standard requirements to address the overall system safety of a connected consumer product. Designers and manufacturers of a connected consumer product, with assistance from conformity...
5.1 The analysis methods in this guide produce data deliverables that may be used to inform: 5.1.1 Technical familiarization (FAA Order 8110.4C, Section 2-3c)?discussions with the certifying authority by means of providing a standardized contextual framework and vocabulary for addressing...
5.1 The laboratory fatigue life determined by this standard for beam specimens has been used to estimate the fatigue life of asphalt mixture pavement layers under repeated traffic loading. Although the field performance of asphalt mixtures is impacted by many factors (traffic...
1.1 This specification covers the requirements for segmental concrete paving slabs used for construction of pedestal-set applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-presse
This guide covers the selection and use of procedures for testing traffic paints in the laboratory and in the field. This guide covers the testing of a ready-mixed paint product of sprayable consistency that shall be suitable for use as a reflecting traffic guide on paved roadways....
4.1 Establishing standard practices and recommended procedures is a critical step required to achieve quality roofing and waterproofing system installations. This guide describes preparing typical substrates to receive hot-applied rubberized asphalt (HRA), melting and application of HRA, typical...
1.1 This specification describes the required properties and test methods for a one or two-component, cold liquid-applied elastomeric-type membrane comprised of silyl-terminated polyether polymer, silyl-terminated polyurethane polymer, or a blend of the two polymers for waterproofing building decks...
1.1 This guide applies to unmanned aircraft (UA) with a maximum dimension (for example, wingspan, disk diameter) =?25?ft (=?7.68 m) operating at airspeeds below 100?kts and of any configuration or category. It is meant to be applied in a "lower risk" (low- and medium-risk airspace as described by...
1.1 This specification covers the requirements for segmental concrete paving slabs manufactured for construction of pedestrian and roof applications for commercial and municipal projects. These slabs can be manufactured with a dry-cast, wet-cast, or hydraulically-presse
Narrow Your Results