loading
MPIF TUNGSTEN METALS - TUNGSTEN, REFRACTORY & HARDMETALS VIII
MPIF
A description is not available for this item.
MPIF TUNGSTEN METALS III - TUNGSTEN AND REFRACTORY METALS III
MPIF
A description is not available for this item.
ASTM B930-03(2026) - Standard Test Method for Rating Grain Size and Frequency of Abnormally Large Grains in Cemented Tungsten Carbides (Hardmetals)
July 1, 2026 - ASTM International

1.1 This test method describes a procedure for measuring abnormally large grains and the frequency of those grains in cemented tungsten carbides (hardmetals). 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility...

ASTM B777-15(2026) - Standard Specification for Tungsten Base, High-Density Metal
July 1, 2026 - ASTM International

1.1 This specification covers the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be...

ASTM B446-26 - Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloy, Nickel-Chromium-Molybdenum-Silicon Alloy, and Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar
July 1, 2026 - ASTM International

1.1 This specification covers nickel-chromium-molybdenum-niobium alloy (UNS N06625), nickel-chromium-molybdenum-silicon alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) in the form of both hot-worked and cold-worked rod and bar in the conditions shown in Table 1...

ASTM E2985/E2985M-26 - Standard Practice for Determination of Metal Purity Based on Elastic Constant Measurements Derived from Resonant Ultrasound Spectroscopy
June 15, 2026 - ASTM International

5.1 Since the beginning of human history, currency has existed in the form of metal coins and bullion. Thieves learned that shaving some precious metal provided a method to change its value. Substitution of common metals for precious metals of higher value was commonplace until weighing methods...

ASTM B168-26 - Standard Specification for Nickel-Chromium-Aluminum Alloys, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Copper Alloy Plate, Sheet, and Strip
July 1, 2026 - ASTM International

1.1 This specification covers rolled nickel-chromium-aluminum alloys (UNS N06699), nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), nickel-chromium-cobalt-molybdenum alloy (UNS N06617), nickel-iron-chromium-tungsten alloy (UNS N06674), and...

ASTM B365-12(2026) - Standard Specification for Tantalum and Tantalum Alloy Rod and Wire
July 1, 2026 - ASTM International

1.1 This specification covers unalloyed and alloyed tantalum rod and wire. 1.2 The materials covered by this specification are: 1.2.1 R05200, unalloyed tantalum, electron-beam furnace or vacuum-arc melt, or both, 1.2.2 R05400, unalloyed tantalum, powder-metallurgy consolidation, 1.2.3 R05255,...

ASTM B663/B663M-26 - Standard Specification for Silver-Tungsten Carbide Electrical Contact Material
February 1, 2026 - ASTM International

This specification covers electrical contact components made from silver-tungsten carbide by powder metallurgical procedures. This specification covers compositions within the silver-tungsten carbide system. The material shall conform to composition limits. Chemical analysis shall be...

ASTM B163-26 - Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
July 1, 2026 - ASTM International

This specification covers seamless tubes of nickel and nickel alloy for use in condenser and heat-exchanger service. This covers outside diameter and average wall, or outside diameter and minimum wall tube. Tube shall be furnished in the alloys and conditions defined by this specification. The...

ASTM B462-26 - Standard Specification for Forged or Rolled Nickel Alloy Pipe Flanges, Forged Fittings, and Valves and Parts for Corrosive High-Temperature Service
July 1, 2026 - ASTM International

This specification covers forged or rolled UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06059, UNS N06686, UNS N08020, UNS N08024, UNS N08026, UNS N08367, UNS N10276, UNS N10665, UNS N10675, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R20033 alloy pipe flanges, forged fittings,...

ASTM B482-25 - Standard Practice for Preparation of Tungsten and Tungsten Alloys for Electroplating
November 1, 2025 - ASTM International

2.1 The proper preparation and processing method choice for electroplating tungsten and tungsten alloys is often critical to the plating's performance. 2.2 This practice outlines recommended procedures to produce adherent finishes on tungsten and tungsten alloys.

ASTM B761-26 - Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation
May 1, 2026 - ASTM International

1.1 This test method covers the determination of particle size distributions of metal powders. Experience has shown that this test method is satisfactory for the analysis of elemental tungsten, tungsten carbide, molybdenum, and tantalum powders, all with an as-supplied estimated...

ASTM A985/A985M-26 - Standard Specification for Steel Investment Castings General Requirements, for Pressure-Containing Parts
April 1, 2026 - ASTM International

This specification covers a group of common requirements that are mandatory for steel castings produced by the investment casting process for pressure-containing parts. Master heats shall be made by the electric furnace process with or without separate refining such as argon-oxygen-decarburization...

ASTM A890/A890M-26 - Standard Specification for Castings, Iron-Chromium-Nickel-Molybdenum Corrosion-Resistant, Duplex (Austenitic/Ferritic) for General Application
April 1, 2026 - ASTM International

This specification covers castings, iron-chromium-nickel-molybdenum corrosion-resistant, duplex(austenitic/ferritic) for general application. Castings shall be heat treated in accordance with the required procedure and heat-treat temperature. Proper heat treatment of these alloys is usually...

ASTM B890-25 - Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
September 1, 2025 - ASTM International

5.1 This test method allows the determination of the chemical composition of powdered and sintered tungsten-based hardmetals. This test method is not applicable to material which will not oxidize readily at high temperatures in air, such as tungsten/copper, tungsten/silver...

ASTM E824-26 - Standard Test Method for Transfer of Calibration From Reference to Field Radiometers
March 1, 2026 - ASTM International

5.1 The methods described represent the preferable means for calibration of field radiometers employing standard reference radiometers. Other methods involve the employment of an optical bench and essentially a point source of artificial light. While these methods are useful for cosine and azimuth...

ASTM A453/A453M-26 - Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels
February 1, 2026 - ASTM International

This specification covers standards for Grade 660 (Class A, B, C, and D) , Grade 651 (Class A and B), Grade 662 (Class A and B), and Grade 665 (Class A and B) of bolting materials for use in high-temperature service such as fasteners, for pressure vessels and valve flanges. Bolting materials in...

ASTM A437/A437M-26 - Standard Specification for Stainless and Alloy-Steel Turbine-Type Bolting Specially Heat Treated for High-Temperature Service
February 1, 2026 - ASTM International

This specifications covers alloy-steel bolting material specially heat treated for high-temperature service, such as steam turbine, gas turbine, and similar uses. The grades of steels covered here are: Grade B4B, Grade B4C, and Grade B4D. Steels of Grades B4B and B4C shall undergo heating, liquid...

ASTM E811-09(2025) - Standard Practice for Measuring Colorimetric Characteristics of Retroreflectors Under Nighttime Conditions
November 1, 2025 - ASTM International

5.1 This practice describes a procedure for measuring the chromaticity of retroreflectors in a nighttime, that is, retroreflective, geometry of illumination and observation. CIE Standard Source A has been chosen to represent a tungsten automobile headlamp. Although the geometry must be...

Advertisement