loading
ASTM D6855-25 - Standard Test Method for Determination of Turbidity Below 5 NTU in Static Mode
November 1, 2025 - ASTM International

1.1 This test method covers the static determination of turbidity in water (see 4.1). 1.2 This test method is applicable to the measurement of turbidities under 5.0 nephelometric turbidity units (NTU). 1.3 This test method was tested on municipal drinking water, ultra-pure...

ASTM D8607-26 - Standard Test Method for Determination of Selected Elements in Aqueous Solutions by Single Quadrupole Inductively Coupled Plasma-Mass Spectrometry (ICP-MS)
July 1, 2026 - ASTM International

1.1 This test method covers the determination of dissolved elements in ground waters, surface waters, and drinking water. It may also be used for determination of total recoverable or total element concentrations in these waters as well as wastewater, mine-impacted waters, and digested biosolids,...

ASTM D6698-25 - Standard Test Method for On-Line Measurement of Turbidity Below 5 NTU in Water
September 15, 2025 - ASTM International

1.1 This test method is applicable to the on-line measurement of turbidity under 5 nephelometric turbidity units (NTU) in water. 1.2 It is the user's responsibility to ensure the validity of this test method for waters of untested matrices. 1.3 In this test method calibration...

ASTM D4188-17(2025) - Standard Practice for Performing Pressure In-Line Coagulation-Flocculation-Filtration Test in Water
December 1, 2025 - ASTM International

1.1 This practice covers the procedure used to perform pressure in-line coagulation-flocculation-filtration of water and waste water. It is applicable to water and waste water with relatively low suspended solids (<30 mg/L). The practice is applicable for any size filter greater than 100 mm (4 in.)...

ASTM D6568-25 - Standard Guide for Planning, Carrying Out, and Reporting Traceable Chemical Analyses of Water Samples
September 1, 2025 - ASTM International

4.1 This guide establishes basic requirements for water and environmental laboratories that generate and report test chemical analyses that the laboratory client desires to be traceable to the SI or to certified reference materials traceable to the SI (Note 1). Traceability of chemical analyses is...

ASTM D6698-24 - Standard Test Method for On-Line Measurement of Turbidity Below 5 NTU in Water
April 1, 2024 - ASTM International

1.1 This test method is applicable to the on-line measurement of turbidity under 5 nephelometric turbidity units (NTU) in water. 1.2 It is the user's responsibility to ensure the validity of this test method for waters of untested matrices. 1.3 In this test method calibration...

ASTM D6855-17(2023) - Standard Test Method for Determination of Turbidity Below 5 NTU in Static Mode
November 1, 2023 - ASTM International

1.1 This test method covers the static determination of turbidity in water (see 4.1). 1.2 This test method is applicable to the measurement of turbidities under 5.0 nephelometric turbidity units (NTU). 1.3 This test method was tested on municipal drinking water, ultra-pure...

ASTM D7725-17(2023) - Standard Test Method for the Continuous Measurement of Turbidity Above 1 Turbidity Unit (TU)
November 1, 2023 - ASTM International

1.1 This test method covers the on-line and in-line determination of high-level turbidity in water that is greater than 1.0 turbidity units (TU) in municipal, industrial and environmental usage. 1.2 In principle, there are three basic applications for on-line measurement set ups. This...

ASTM D7315-17(2023) - Standard Test Method for Determination of Turbidity Above 1 Turbidity Unit (TU) in Static Mode
November 1, 2023 - ASTM International

5.1 Turbidity at the levels defined in the scope of this test method are often monitored to help control processes, monitor the health and biology of water environments and determine the impact of changes in response to environmental events (weather events, floods, etc.). Turbidity is...

ASTM D7726-11(2023) - Standard Guide for The Use of Various Turbidimeter Technologies for Measurement of Turbidity in Water
November 1, 2023 - ASTM International

1.1 This guide covers the best practices for use of various turbidimeter designs for measurement of turbidity in waters including: drinking water, wastewater, industrial waters, and for regulatory and environmental monitoring. This guide covers both continuous and static measurements. 1.1.1...

ASTM D5092/D5092M-16(2024) - Standard Practice for Design and Installation of Groundwater Monitoring Wells
June 15, 2024 - ASTM International

1.1 This practice describes a methodology for designing and installing conventional (screened and filter-packed) groundwater monitoring wells suitable for formations ranging from unconsolidated aquifers (that is, sands and gravels) to granular materials having grain-size distributions with up to 50...

ASTM D6699-24 - Standard Practice for Sampling Liquids Using Bailers
May 1, 2024 - ASTM International

5.1 A bailer is a device for obtaining a sample from stratified or un-stratified waters and liquid wastes. The most common use of a bailer is for sampling ground water from single-screened wells (Fig. 1) and well clusters (see Guide D4448). 5.2 This practice is applicable to sampling water and...

ASTM D8002-24 - Standard Test Method for Modified Fouling Index (MFI-0.45) of Water
April 1, 2024 - ASTM International

1.1 This test method covers the determination of the modified fouling index (MFI) of water measured at constant pressure. This test can be used to indicate the fouling potential of reverse osmosis/nanofiltration (RO/NF) feed water due particulate matter and is applicable to low and high...

ASTM D7512-09(2023) - Standard Guide for Monitoring of Suspended-Sediment Concentration in Open Channel Flow Using Optical Instrumentation
December 15, 2023 - ASTM International

1.1 This guide covers the equipment and basic procedures for installation, operation, and calibration of optical equipment as a surrogate for the continuous determination of suspended-sediment concentration (SSC) in open channel flow. 1.2 This guide emphasizes general principles for the application...

ASTM D7937-15(2023) - Standard Test Method for In-situ Determination of Turbidity Above 1 Turbidity Unit (TU) in Surface Water
July 1, 2023 - ASTM International

5.1 Turbidity is monitored to help control processes, monitor the health and biology of aquatic environments and to determine the impact of environmental events such as storms, floods, runoff, etc. Turbidity is undesirable in drinking water, plant-effluent waters, water for food and...

ASTM D6725/D6725M-16(2024)e1 - Standard Practice for Direct Push Installation of Prepacked Screen Monitoring Wells in Unconsolidated Aquifers
March 15, 2024 - ASTM International

1.1 This practice is based on recognized methods by which direct push monitoring wells may be designed and installed for the purpose of detecting the presence or absence of a contaminant, and collecting representative groundwater quality data. The design standards and installation procedures herein...

ASTM D4189-23 - Standard Test Method for Silt Density Index (SDI) of Water
November 1, 2023 - ASTM International

1.1 This test method covers the determination of the silt density index (SDI) of water. This test method can be used to indicate the quantity of particulate matter in water and is applicable to relatively low (<1.0 NTU) turbidity waters such as well water, filtered water, or clarified...

ASTM D8297/D8297M-23 - Standard Test Method for Determination of Erosion Control Products (ECP) Performance in Protecting Slopes from Sequential Rainfall-Induced Erosion Using a Tilted Bed Slope
November 1, 2023 - ASTM International

5.1 This test method utilizes large-scale testing equipment and procedures established at a variety of testing laboratories over the last 30 years. 5.2 This method is useful in evaluating ECPs and their installation to reduce soil loss and sediment concentrations when exposed to defined rainfall...

ASTM D8298/D8298M-23 - Standard Test Method for Determination of Erosion Control Products (ECP) Performance in Protecting Slopes from Continuous Rainfall-Induced Erosion Using a Tilted Bed Slope
November 1, 2023 - ASTM International

5.1 This test method utilizes large-scale testing equipment and procedures established at a variety of testing laboratories over the last 30 years. 5.2 This method is useful in evaluating ECPs and their installation to reduce soil loss and sediment concentrations when exposed to defined rainfall...

ASTM D4012-23a - Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Water
November 1, 2023 - ASTM International

5.1 A rapid and routine procedure for determining biomass of the living microorganisms in cultures, waters, wastewaters, and in plankton and periphyton samples taken from surface waters is frequently of vital importance. However, classical techniques such as direct microscope counts,...

Advertisement