1.1 This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants...
La Norma riveste un carattere di ampia generalità ed è applicabilie a tutti i prodotti elettrotecnici ed elettronici, fatte salve le integrazioni che ogni Comitato Tecnico ritiene utile apportare. Per tutto il vasto campo delle prove climatiche e meccaniche fondamentali, fissa la terminologia,...
Diese Norm gilt für Griffe für Ultraschallreinigung
1.1 This practice covers a procedure for the cleaning of materials and components used in systems requiring a high level of cleanliness, such as oxygen, by ultrasonic techniques. 1.2 This practice may be used for cleaning small parts, components, softgoods, etc. 1.3 The values...
4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...
1.1 This practice2 covers general ultrasonic testing procedures for the detection of discontinuities in the weld and adjacent heat affected zones of welded pipe and tubing by scanning with relative motion between the search unit and pipe or tube. When contact or unfocused immersion search...
1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...
This practice covers the standard recommendations and precautions for cleaning, descaling, and passivating of new stainless steel parts, assemblies, equipment, and installed systems. Consideration shall be given in the design of parts, equipment, and systems that will require cleaning...
This specification covers precipitation hardened iron base superalloy forgings which are primarily intended for use as turbine rotor disks and wheels. Two heat treatments are covered and selection will depend upon design, service conditions, mechanical properties, and elevated temperature...
1.1 The purpose of this guide is to establish a procedure to select cleaning agents, both solvents and water-based detergents, for oxygen-enriched systems. This includes laboratory-scale tests for cleaning effectiveness, materials compatibility, and oxygen compatibility. 1.2 The...
1.1 This practice may be used to extract nonvolatile and semivolatile residues from materials such as new and used gloves, new and used wipes, component soft goods, and so forth. When used with proposed cleaning materials (wipes, gloves, and so forth), this practice may be used to determine...
This specification deals with the procedures and acceptance standards for straight beam, pulse echo, ultrasonic examination of rolled structural shapes. The section surfaces shall be sufficiently clean and smooth to maintain a back reflection from the opposite side of the flanges,...
This specification defines test methods and performance criteria for ultrasonically welded wire-to-terminal bonds as shown in Figure 1 . This specification subjects parts to environmental exposures to simulate a lifetime of field exposure for a road vehicle. Exposures referenced in this...
1.1 This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants...
1.1 This test method covers a procedure for evaluating the effectiveness and capability of cleaning agents to remove contamination to the desired level. This includes removing drug residues from manufacturing equipment and residues from medical devices (Guide E3106), as well as systems for...
1.1 This practice covers a procedure for measuring the ultrasonic velocities in the outer wall of polyethylene storage tanks. An angle beam lateral longitudinal (LCR) wave is excited with wedges along a circumferential chord of the tank wall. A digital ultrasonic flaw detector is used...
1.1 This practice2 describes general ultrasonic testing procedures for the detection of discontinuities in the weld and adjacent heat affected zones of welded pipe and tubing by scanning with relative motion between the search unit and pipe or tube. When contact or unfocused immersion search...
Narrow Your Results