1.1 This practice describes the minimum live loads and dead loads to be applied when designing monolithic or sectional precast concrete utility structures. Concrete pipe, box culverts, and material covered in Specification C478/C478M are excluded from this practice. Note 1: For additional...
5.1 General Utility: 5.1.1 This practice is suitable for research, quality control, specification testing and process control. 5.1.2 It is useful to define and verify the reactivity of non-foam polyurethane formulations. 5.2 Limitations: 5.2.1 Operator-to-operator
1.1 This specification covers ductile iron transmission and distribution utility poles. 1.2 The values stated in inch-pound units are to be regarded as standard. The SI values given are mathematical conversions that are provided for information only and are not considered standard. 1.3 The...
6.1 The primary goal of this practice is to extract representative samples from PV modules for TCLP toxicity testing purposes in order to receive unbiased, comparable, and repeatable toxicity test results from independent TCLP testing laboratories. 6.2 Solar photovoltaic (PV) modules in the United...
3.1 Viscosity has significance in the use of emulsified asphalts because it is a property which affects their utility. When used in application types of construction, the material must be thin enough to be uniformly applied through the spray bar of distributor, yet thick enough so that it...
This practice covers the procedures to be followed in the planning, site preparation, and installation of underground precast concrete utility structures. The installation area shall be surveyed using the workprint and a checklist to identify the work to be done and to determine that the...
4.1 Uses-This practice is intended for use by federal agencies, and environmental professionals in order to facilitate ECP efforts. It is also intended for use by preparers and reviewers of environmental condition of property maps and ECP reports used to support CERFA uncontaminated property...
This specification establishes the requirements for non-essential ice detection system aspects of airworthiness and design for aeroplanes. The term "aeroplane" as used in this specification was originally conceived for normal category fixed wing aircraft with a certified maximum takeoff weight...
1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, and material covered in Specification C478/C478M. 1.2 The values stated...
1.1 This guide helps describe the laboratory informatics landscape and covers issues commonly encountered at all stages in the life cycle of laboratory informatics from inception to retirement. It explains the evolution of laboratory informatics tools used in today's laboratories such as laboratory...
4.1 This practice is intended for use whenever the dynamic characteristics of an amusement ride or device are to be determined. The existence of this practice is not intended to imply that there is a requirement to perform specific testing on amusement rides or devices. 4.2 The general provisions...
5.1 The pour point of a petroleum product is an index of the lowest temperature of its utility for certain applications. Flow characteristics, like pour point, can be critical for the correct operation of lubricating oil systems, fuel systems, and pipeline operations. 5.2 Petroleum blending...
5.1 The pour point of a petroleum product is an index of the lowest temperature of its utility for certain applications. Flow characteristics, such as pour point, can be critical for the correct operation of lubricating systems, fuel systems, and pipeline operations. 5.2 Petroleum blending...
5.1 The pour point of a petroleum product is an index of the lowest temperature of its utility for certain applications. Flow characteristics, such as pour point, can be critical for the correct operation of lubricating systems, fuel systems, and pipeline operations. 5.2 Petroleum blending...
5.1 This test method is part of an overall suite of related test methods that provides repeatable measures of robotic system maneuverability. The ability of an aerial robot to navigate through apertures increases its utility and survivability for various missions that may be performed in...
1.1 This test method covers the determination of the molar mass of chitosan and chitosan salts intended for use in biomedical and pharmaceutical applications as well as in tissue-engineered medical products (TEMPs) by size exclusion chromatography with multi-angle laser light scattering detection...
1.1 This specification covers corrugated steel structural plate, zinc-coated, used in the construction of pipe, pipe-arches, arches, underpasses, and special shapes for field assembly. Appropriate fasteners and accessory materials are also described. The pipe, arches, and other shapes are generally...
5.1 This test method is part of an overall suite of related test methods that provide repeatable measures of robotic system maneuverability. The ability of an aerial robot to land and takeoff in varied environments increases its utility and survivability for various missions that may be...
1.1 This practice describes a procedure for detecting subsurface flaws in composite panels and repair patches using flash thermography (FT), in which an infrared (IR) camera is used to detect anomalous cooling behavior of a sample surface after it has been heated with a spatially uniform light...
1.1 This specification covers corrugated steel structural plate, polymer-coated, used in the construction of pipe, pipe-arches, arches, underpasses, and special shapes for field assembly. Appropriate fasteners and accessory materials are also described. The pipe, arches, and other shapes are...
Narrow Your Results